Recent content by impy101

  1. I

    PS2 Mars-Pro OPL guide?

    I did not know that. Will stick with Modbo in the future then.
  2. I

    PS2 Mars-Pro OPL guide?

    I thought the whole point of a modchip was so that you wouldn't have to mess around with soft mods. Besides, with modbo would you really need FMCB when the chip already loads all the apps you want?
  3. I

    PS2 Mars-Pro OPL guide?

    So I've been hearing more and more about this Mars-Pro chip and it's superiority over Modbo (better protection, better media support etc) and I've got one successfully installed in a 9000x console. But I can't find any information on how to get it to run OPL or anything of that sort. Any help is...
  4. I

    Modded switch won't boot

    I have the Picofly installation method. Not the HWFly with the ribbon cable etc. 1729110772 Not possible. If that was the problem then the switch would've worked and booted to OFW when I disconnected the modchip and the MicroSD card.
  5. I

    Modded switch won't boot

    Quite a while back. It was working fine. I don't know what changed to be honest..
  6. I

    Modded switch won't boot

    Not the latest, but they are both the same version. I can't check since the switch won't both to either..
  7. I

    Modded switch won't boot

    Both are latest versions 1729107324 Besides, it doesn't even boot in OFW. Even when I disconnect the modchip to boot directly to OFW it does nothing..
  8. I

    Modded switch won't boot

    I got a modded V2 here that refuses to boot. Hekate boots up fine, so that means the modchip and the wiring is all fine, but as soon as I try to launch emummc or even reboot to OFW it won't do anything. It just hangs there on a black screen. I thought it could be a bad emmc, but I did a...
  9. I

    Switch OLED trace broken

    Hello, A customer of mine tried to mod his switch OLED using the so-called "kamikaze"-method. In doing so he appears, to me anyway, to have broken the trace near the A point resistor. Does anyone know where this trace goes so I can solder a wire to restore it? I can't find any schematics..
  10. I

    RP2040 2 flashes

    I've already replaced the cpu flex and that did not do anything. Here are some pics. I've grinded away as you can probably see so that I could test for continuity and that was all fine as well, so I really don't know what's causing this.
  11. I

    RP2040 2 flashes

    Hello, I have a switch V1 here that's giving me a lot of trouble. I have installed both a Picofly and a HWFLY and none of them want to work. I keep getting 2 flashes. Pretty sure they are fast flashes which suggests RST is not connected, causing the switch to start up normally, but even with...
  12. I

    XY-SP5W mod guide?

    I got a XY-SP5W board that I want to install in my GBA, but I have been searching the internet all day and I cannot find any guides for it at all. Not even a wiring diagram. I was hoping someone here could help me with this.
  13. I

    Hacking Sigpatches for Atmosphere (Hekate, fss0, fusee & package3)

    It certainly is a big step in the right direction. Thanks for sharing and massive shout out to the modders :)
  14. I

    Hacking Sigpatches for Atmosphere (Hekate, fss0, fusee & package3)

    You gotta downgrade CFW back to 16.1.0
  15. I

    Nyx exception occurred

    I have something I have never encountered before. A switch OLED that refuses to boot into Hekate for longer than a couple of seconds because I get the following error code: Nyx exception occurred (LR 8102986C) I have tried a different SD card, I have redownloaded Nyx and Hekate and placed them...
See more