Recent content by idSkeetOnU

  1. I

    Hacking Hardware Picofly - a HWFLY switch modchip

    thanks for the info. would a v4.1 hwfly flex cable set do? do i need a dat0 adapter? sorry for the all the questions. im trying to order a set and would like the right one
  2. I

    Hacking Hardware Picofly - a HWFLY switch modchip

    hello everyone, im interested in doing this install. i have a v1 trinket switch and have been reading about the rp2040 zero install but dont know how to start. im looking to buy a oled switch and am wondering if a certain version is better than another. also which version hwfly flex cables...
  3. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    i think u need vol+ strap to be able to shutdown system then powerup to cfw. if not u stuck with dualboot. the alt point on back of board is what i used. very easy to solder to.
  4. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    if u have trinket soldered with 7 straps then u can change autoboot cfw to dualboot or vice versa. when switch is powered on then long press vol+ and trinket will blink. thats it no need for autorcm
  5. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    how do i put it in dual boot mode?
  6. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    thanks for all the help mrdude i do appreciate it. so that no usb voltage not found normal for all trinket users? also i notice it autoboots cfw and not dual boot so when the system is shutoff and then plugged in it goes into rcm. is this because its running autorcm. i have autorcm turned...
  7. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    nevermind. i figured it out. had to double press reset while screen is sleeping. then plug in usb cable. now to figure out how uf2 settings work 1671290397 hello i have another question. in the fusee menu info page is my usb voltage check suppose to show not found yet?
  8. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    i kinda assume the vol+ thing just wanted to make sure
  9. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    ok, so i just finished installing the trinket chip and i did the 7 strap install. i have a question, how do i enter the trinket now if i needed to flash new files over? also i notice when i press on back on switch and press the trinket reset button it raises the volume+. is that normal?
  10. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    do u happen to have any pictures of how u routed wiring or after pics
  11. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    one last question. would u recommend the 3v pad near joycon pads on front or the 3.3v pad on back for power? i assume the .3v difference doesnt matter 1671209318 from the looks of the alternate pads on back, i would probably go joycon, usb disconnect, 3.3v and vol+ on back and usb d+d- and...
  12. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    if i were to remove the board can i only tap into the vol+ strap or do all my straps need to be connect on back also. sorry for the dumb question.
  13. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    ive opened my switch and inspected the vol+ strap and i dont want to connect that, as i only want dual boot anyways. can i still use this fusee trinket mod?
  14. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    ok so i flashed the part 1 trinket uf2 file and the window closes and reopens and now its called fusee. i flash part 2 trinket uf2 and it asks to overwrite file. is that was is suppose to happen? also which settings uf2 file should i use if i only want dual boot and red splash?
  15. I

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    ok. thanks for the help. do u use the newest 9.2.1 or a different version?
See more