Recent content by glitcher

  1. G

    sysNAND brick or is there hope?

    Ok, I understand, I have some issues with crashing when plugging in a game card, maybe I will try if the maintenance mode works now...
  2. G

    sysNAND brick or is there hope?

    Ok, wait, I can boot into sysNAND now!! :toot: What I did was booting the following boot entry (as I think Atmosphere on sysNAND): [Atmosphere PKG3 sysMMC] pkg3=atmosphere/package3 kip1=atmosphere/kips/* emummc_force_disable=1 icon=bootloader/res/sys_cfw_boot.bmp After that I could boot and set...
  3. G

    sysNAND brick or is there hope?

    No, just Level 3 repair from NAND Fixer Pro with my own prod.keys and a downloaded Firmware (update). So, you got into maintenance mode as shown in the video? Also on the emuNAND? Did you also try using the tegra explorer system wipe? This also didn't work for me... Do you mean sd:/emuMMC/RAW1...
  4. G

    sysNAND brick or is there hope?

    I tried that: boot into hekate -> Launch emuNAND -> Hekate loading Screen -> Atmosphere screen -> when atmosphere screen is gone pressing + and - at the same time -> Switch logo appears -> Atmosphere Error from above. What did I do wrong? 1782663973 The Atmosphere error "2162-0002 (0x4a2)" is...
  5. G

    sysNAND brick or is there hope?

    I have a boot delay of 3s and it just boots into Hekate, guess there is no recovery partition... I managed to get through Level 3 recovery! But it does not boot at all. When I select Tools -> Restore eMMC -> eMMV Boot0 & BOOT1, then I am getting the warning "Size of the SD Card Backup does not...
  6. G

    sysNAND brick or is there hope?

    Sadly, the Switch seems to need a first boot to convert the prod.keys, because it's still the same file and NAND fix pro still thinks it's encrypted... 1782582939 I tried, but when doing that it just boots into Hekate... I also tried a factory reset using Tegra Explorer without success.
  7. G

    sysNAND brick or is there hope?

    Yes that would be the easy solution, sadly I did everything wrong with that console... I tried the "EmmcHaccGen.GUI" and generated a new FW using a stock FW19 and flashed it using lockpick. At least it shows the first logo and then only the black screen. The fuses are now "ODM 7/6: 20|0 - HOS...
  8. G

    sysNAND brick or is there hope?

    Yes sure, I did so! But I can only extract from FW11 because that is what my sysNAND is (was) on. I tried again which resulted in the same file (only 200 lines)...
  9. G

    sysNAND brick or is there hope?

    I am only able to access the sysNAND FW11 where I have the prod.keys from using lockpick...
  10. G

    sysNAND brick or is there hope?

    Sadly not, I would restore if I would have been more careful...
  11. G

    sysNAND brick or is there hope?

    I have no idea, because it's not booting... Can i check that?
  12. G

    sysNAND brick or is there hope?

    Hi all! I have a Switch Mariko which has a sysNAND whch (was or is) on FW11 which I did not boot for about 5 years. The sysNAND booted to the second N* Switch logo and stuck there. I deleted my FW19 emuNAND to make a fresh install not knowing that my stock FW is not booting. Therefore I need to...
  13. G

    Hacking Sigpatches for Atmosphere (Hekate, fss0, fusee & package3)

    I was wrong it still does not start! I accidentially started CFW sysMMC and it worked there... I compleytely formatted my SD card, re-installed Atmosphere andre-created emuMMC. Then I just used the mentioned sys-patches. Still the software is ended with the error message, no matter if I start a...
  14. G

    Hacking Sigpatches for Atmosphere (Hekate, fss0, fusee & package3)

    Thanks alot! sys-patch 1.5.6 in combination with the latest sigpatches worked! I also used the following bootloader/hekate_ipl.ini content (I have no idea if all settings are right, but that worked): [config] autoboot=0 autoboot_list=0 bootwait=0 autohosoff=0 autonogc=1 updater2p=1 backlight=100...
  15. G

    Hacking Sigpatches for Atmosphere (Hekate, fss0, fusee & package3)

    Hi all! I am new to this forum. Yesterday I installed a modchip into a newly bought Switch OLED, installed Hekate (6.4.2, latest) and Atmosphere (1.10.1, latest) on an emuMMC SD card. Due to an issue installing Tinfoil I downgraded from FW 21.2 to 20.0.0 succesfully. My current problem is...
See more