Recent content by frangato

  1. F

    My OLED freezes when I run any game.

    I checked the thermal paste, and although it wasn't bad, I replaced it with new paste. The fan works perfectly. The problem persists. I've even considered the possibility of a faulty NAND flash memory and creating a new one (donated) since I don't mind getting banned if it solves the problem...
  2. F

    My OLED freezes when I run any game.

    I'm having a problem with my OLED Switch. It freezes when I run games. If I'm not playing games, the console works perfectly fine, but it only freezes when I'm playing games. I've tried removing the Instinct mode, and it still does the same thing in official mode. I've also tried resetting it to...
  3. F

    Values of these resistors of an OLED

    Very thanks.
  4. F

    Hardware I'm looking for these capacitors for the Switch OLED

    Thank you. I have measured the horizontal ones and they all give me 150 ohms. Are the verticals also resistances? The values it gives me are different in each one. Could you tell me what values or if they are resistors or capacitors of the 3 in this photo? Is 0603 100 pf?
  5. F

    Values of these resistors of an OLED

    I assume that the vertical ones are 150 ohm resistors, and the horizontal ones according to the other photo are 74 pf capacitors? It's just that between the two photos it confuses me. Thank you so much. Thank you. I have measured the horizontal ones and they all give me 150 ohms. Are the...
  6. F

    Values of these resistors of an OLED

    Could someone tell me the value of these resistors, of the OLED switch, if they are all the same value? They don't give me the same measurements and I have problems with them on the volume and Power buttons. Thank you so much.
  7. F

    Resistance Measurements

    Very good and I thank you in advance for your help. Could someone help me by telling me the model of these resistors that I can't find so I can change them to a problematic OLED? Thank you.
  8. F

    Problem with volume button - in nintendo switch Oled when installing hwfly v4

    One of the pins is making bad contact when it was inserted, it must have been twisted and that caused it to break down, what I did was change the motherboard connector for a new one and it worked fine again. Greetings.
  9. F

    installing hwfly 4.1 on switch lite please help ! chip not attaching

    Does anyone know or can decipher the order of the points to be able to solder through cables in case the flex is screwed up? I have one that I don't have on the flex because it arrived damaged, but I want to take advantage of it, the bad thing is that I don't know the order of the points on the...
  10. F

    Help installing Hwfly v4 on Erista Patched

    Good friend, did you manage to solve the problem?, what scheme did you use, could you put a photo or scheme? I'm in the same situation with a v1 and I can't get it to work with an oled chip. Thank you very much.
  11. F

    Is there any way or diagram to install the ole chip in the patched v1?

    Good morning friends, is there any way or diagram to install the ole chip in the patched v1? What possibilities are there? Thank you very much.
  12. F

    Hardware Switch serial number beginning with XFL7???

    That serial number is from the dock, with that you don't do anything or know anything about the console, the console's serial number is on the bottom edge, or in the case of oled behind the SD cover.
  13. F

    Problem with volume button - in nintendo switch Oled when installing hwfly v4

    I have seen the other thread, but it is not about the ignition flex, I have tried another one that is perfect and makes the same error. The volume button still doesn't work. In the other console I have tried the felx that is failing me and all the buttons work perfectly, I am inclined that the...
  14. F

    Problem with volume button - in nintendo switch Oled when installing hwfly v4

    CompSciOrBust I usually buy them on Aliexpress in this store, recommended by Sthetix, but I put the firmware r 0.30 because 0.62 gives boot problems over time. But only this one has failed me, could it be that the chip is defective? The pauload checker gives me this warning, I think it is not...
  15. F

    Problem with volume button - in nintendo switch Oled when installing hwfly v4

    Thank you, I have tried another flat cable, and the problem persists, it makes me indicate that it may be some resistor or capacitor blown when starting up for the first time with the hwfly, since the power button and the volume + button are working perfectly, but the volume-no, which is the one...
See more