Recent content by FonzT

  1. F

    No homebrews after dead battery

    Hi. Yes, it sometimes works, sometimes not. I managed to play one Vita game and one PSP game... Sometimes it works flawlessly, sometimes it just hangs and sd2vita starts acting up. I don't know if it's due to some plugin, even tho I was NOT having problem before putting my Vita in the closet...
  2. F

    No homebrews after dead battery

    Thank you all. Right now, I am using a Sandisk one and it's working perfectly. But I get some errors about apps being corrupted or to redownload apps after some minutes I connect the console to the internet. I have spoofing on and my account is not banned. What's happening?? If I try to hard, I...
  3. F

    No homebrews after dead battery

    Hi. Sincerely I don't know!!! Anyway, I just started my Vita up and NOW it seems to ALWAYS recognize the sd2vita on uma0... But if I switch partitions in YAMT settings, I don't get all the bubbles (I don't get VitaDeploy either!!) and they don't start at all with generic errors or errors says...
  4. F

    No homebrews after dead battery

    Thank you for you replies. sd2vita was working really good, until the battery died. It's not the first time I let the battery die, but this time it sat for some months... I can't explain this...
  5. F

    No homebrews after dead battery

    Thanks for your replies. I am using YAMT btw... The sdcard works on my computer. Anyway I ordered yet another sd2vita, but the black one this time.... even if I think they are the same inside as the white ones
  6. F

    No homebrews after dead battery

    Hi. Thanks for your reply. I just ordered a new sd2vita adapter. Today it arrived at home and tried it. I set ux0 as Sony memory card and uma0 to sd2vita. uma0 was showing, but after reboot it was simply gone. Reinserting the adapter sometimes fixed it... but it was not reliable. Why is this...
  7. F

    No homebrews after dead battery

    Hi! My PS Vita was working fine, until the battery was dead. I turned it on after few months and my homebrews cannot start because it was saying to redownload and other errors. So it did VitaDeploy. I am on Enso 3.65. After a reboot, the PSVita rebuilt the databsae on its own and all the apps...
  8. F

    Hardware No backlight Switch Lite (no 17v)

    Hi. Check my latest thread. I posted the solution in last reply.
  9. F

    Switch Lite no backlight

    I solved my problem. It was: 1. burned out wide connector on daughter board 2. burned out FPC cable, around bigger vias (gold turned gray) 3. faulty backlight on LCD itself
  10. F

    Switch Lite no backlight

    Hi y'all. I just checked for voltage among the two feedback pins and high volt rail. They have almost equal voltage, around 3.4ish volts... So they are not drawing any current at all? Because they should have potential different, otherwise no current is drawn. Right? Does this indicate fault in...
  11. F

    Switch Lite no backlight

    Hi. Thanks for your reply. I already replaced the ribbon cable and the daughter board itself. All buttons on daughter board are working. It's just the 17v rail which is not 17 volts, but it's around 3.4 volts... I see NO signs of corrosion.
  12. F

    Switch Lite no backlight

    Hi. Thanks for your reply. I tried disconnecting the entire game cart board, but nothing changes. Anyway, I don't think what that board has to do with the backlight. If it's helpful, I get 3.3v at VIN of the backlight IC... is this correct?
  13. F

    Switch Lite no backlight

    Hi y'all. I already saw a lot of topics here and there, but I could not figure out what's going on with my Switch Lite. Basically, there is no backlight, but I can see the screen if I shine a light to it. I already replaced the ribbon connector and the daughter board itself. All the buttons...
  14. F

    Hardware No backlight Switch Lite (no 17v)

    Hi y'all. I just run into this issue with my Switch Lite. I don't get any diode reading on backlight connector (the 4 pin one with GND as last pin). How is this possible? Main-to-daughter board connector seems ok and continuity seems to be there. It's just the diode reading that's not beeping at...
  15. F

    Hardware Question on Pico modchip clones

    Hi y'all. I'm thinking about modding my OLED Switch, since I barely play offline, so I don't care about online play. I am pretty handy with soldering iron. I successfully serviced various PS3 and RGHed two Xbox 360s (by "servicing", I mean regularly changed thermal paste, CMOS battery, removed...
See more