Recent content by Ferz1984

  1. Ferz1984

    Switch OLED slow speed on SD CARD Current rate of 25 MB/s (50 MHz) !!

    I have tested the 2 sd that I have posted... I believe that they are both a1 card's... I will try to find an a2 card just to check..but I think that something is wrong with the mainboard... maybe I knocked off something when installing the picofly.... 1760976258 Just an update I check with a new...
  2. Ferz1984

    Switch OLED slow speed on SD CARD Current rate of 25 MB/s (50 MHz) !!

    I know but what is the cause of 25MB/s ?? What to check? 1760937473 All the cards have the same results in Oled switch... they all work in 25MB/s in other switches i have tested they work in 104 MB/s... something is wrong with the motherboard i believe... but I don't know what is causing this...
  3. Ferz1984

    Switch OLED slow speed on SD CARD Current rate of 25 MB/s (50 MHz) !!

    Hey everyone, hope you’re all doing well! I’m reaching out because I really need some help and I’m not sure what exactly to look for. I have a Switch OLED that seems to have an issue with the SD card speed. It’s showing very low read/write performance. I should mention that the problem is...
  4. Ferz1984

    Rp2040 OLED error code help!

    ok, that's nice I will send you a pm... let's go for the 64 GB I will upload the image on my Google Drive..
  5. Ferz1984

    Rp2040 OLED error code help!

    I will order a new 64 GB chip from Ali just to be sure it will be ok... because the old one has had too much heat... I will send you also the 128 GB to see if you can also write the image there.... maybe I ruined it also... (I don't know...) so I have to wait for the chip and I will contact you...
  6. Ferz1984

    Rp2040 OLED error code help!

    The problem is that i don't have a programmer to write the image... I have kept Boot 0 , Boot 1 and a whole image of the original nand... I have tried the new emmc and nothing....it gives me yellow light error...not even trying to glitch...
  7. Ferz1984

    Rp2040 OLED error code help!

    So i have an update.... Finally, the nand stencils arrived so i reball the original nand chip to give it a try, i solder it back and now i have a blue light trying to glitch and after 40 -50 seconds turns to white and again blue flashing about 40-50 secs and 3 yellow at the end and stops... 1...
  8. Ferz1984

    Rp2040 OLED error code help!

    in some threads, some users say it is possible to boot with an empty nand... :wtf::wtf::wtf:
  9. Ferz1984

    Rp2040 OLED error code help!

    so is there any easy method to create the 4mb boot partition? i don't have a programmer to write the backup to the chip... i
  10. Ferz1984

    Rp2040 OLED error code help!

    No i have a corrupted nand chip... I have replace it and i want to boot to hekate to restore the backup to new chip..
  11. Ferz1984

    Rp2040 OLED error code help!

    With cables i have the same problem..
  12. Ferz1984

    Rp2040 OLED error code help!

    Should i try without the flex cable ? Just with wires? I have checked all the contacts with my multimeter and i get good readings..
  13. Ferz1984

    Rp2040 error code help! Oled

    Can anyone identify this error code ? I can't find ot on GitHub.. *== or *=* ?? I dont know... Any help appreciated
  14. Ferz1984

    Rp2040 OLED error code help!

    Hello , What is this error code ? I can't find it on GitHub... *== or *=* i dont know.. Any help appreciated...
  15. Ferz1984

    Switch Oled emmc replaced

    ok, i will remove the nand, reball it and try again...
See more