Recent content by EM1_1

  1. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    I think the NAND might be corrupted since when i reverted it to stock it turns off a second after turning it back on (wires desoldered)
  2. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    I did the alternate solder point (almost killing the GPU_RST_DONE point in the making :p) but it still doesn't boot, while doing that "ticking" sound. I have modded my friend's corona before and I don't recall it doing this (ticking), I only remember it spinning the fan at full speed because of...
  3. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    Sorry for the late response. Yeah i forgot to look at the folder of the bad update usb for the nanddumps. The thing is that i put the bad update stuff on a bad usb (which i didn't knew was bad at the time) and the usb put itself on read only mode as a way to protect the flash storage, I copied...
  4. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    I got the cpu key beforehand from the BadUpdate nand flasher (READ ONLY) Edit: the cable with the resistor dangles ever so slightly (too long?) could that be an issue? Or is my issue more related to a bad nand dump/write? I used the wiring shown in ConsoleMods w/ the MTX SPI since that's the...
  5. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    You might be right, i'll try hooking up the wires tomorrow and checking the connection
  6. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    I hear a very low "ticking" sound coming from the fan (heatsink/cpu?), idk if that's supposed to happen in Trinity's while glitching? 1754885330 At first when I did the backup JRunner automatically did 2 backups and i put them on a separate untouched directory. A few days after of struggling I...
  7. EM1_1

    Xbox 360 Trinity RGH3 not booting to Xell/Dashboard

    Hello, I recently modded a trinity x360 w RGH3 with a 5.1k resistor (i've already tried 3k, and 10k beforehand with the same results). The console turns on w a blinking green LED (cuz of no DVD Drive) but it doesn't boot or output anything to the screen. The PCB has some scratched traces, but i...
  8. EM1_1

    Hardware Misc Wii U Red Blinking light

    I measured both with the DC Volts setting (2v and 20v), depending on what voltages i should’ve gotten according to the picture (standby and powered on). And i also double checked every rail with continuity mode.
  9. EM1_1

    Hardware Misc Wii U Red Blinking light

    Omg the linked thread is so helpful tysm!!!!! 1742868753 I narrowed down the cause of my problem to a short on the power rails, since in voltage mode, the only one that gives me a reading is the standby 15V rail (purple in the linked picture), the other ones straight up don’t send any voltage...
  10. EM1_1

    Hardware Misc Wii U Red Blinking light

    I received a wii u with the RBLoD. I already cleaned, repasted, and checked the power supply and everything seems fine. I know it has to do with a power rail in the console or a buck converter but I couldn’t find any information about it. Also, it doesn’t flash a blue light after the power...
  11. EM1_1

    Hacking Hardware Nintendo Switch OLED not turning on after not so successful Picofly mod attempt

    Yeah, i found out that one of the cables shorted out something and burnt a fuse above the USB C port and possibly burnt the M92. Does anyone know what value is that fuse on top of the USB C port? 1738129262 I have decided to desolder everything and if I make it work to never touch again and/or...
  12. EM1_1

    Hacking Hardware Nintendo Switch OLED not turning on after not so successful Picofly mod attempt

    Oh I didn’t know that. I’ll try to do that when i get home and i’ll post an update. Also, what is the method for digging holes for the CMD?
  13. EM1_1

    Hacking Hardware Nintendo Switch OLED not turning on after not so successful Picofly mod attempt

    Hi, I finished soldering my RP2040 in my OLED and after connecting the battery and the screen when i plug it into a charger it does nothing, normally it would either flash purple (poor clk soldering) or a charging icon (normal) but now it does nothing and the RP2040 doesn’t flash any codes, or...
  14. EM1_1

    O3DSXL’s charge doesn’t go to the battery. Only works while charging.

    Wouldnt the 3DS just not turn on at all if the IC was defective? or am I confusing some other IC? Also, how can I check if its defective/what should the normal voltage readings be? thanks
  15. EM1_1

    O3DSXL’s charge doesn’t go to the battery. Only works while charging.

    Hi, My friend gave me his 3DS XL to repair since his 3rd party charger blew the F1/F2 fuses, or so we thought. Symptoms: 3DS won’t charge at first but turns on. I removed and bridged the F2 fuse for the meantime while the fuse arrived; turns on but still wont charge (only works while plugged...
See more