Recent content by eliasrs

  1. E

    Hacking NXDumpTool dump removal

    The files under that folder are just 20+ char long random strings
  2. E

    Hacking NXDumpTool dump removal

    Would that be ”unused tickets” under console content manager?
  3. E

    Hacking NXDumpTool dump removal

    Just want to make sure no traces of the certs are left on my switch so the carts get banned. Will remove those certs and install as NSP, but no certs are used from another location on my switch right?
  4. E

    Hacking NXDumpTool dump removal

    Oh, and I'm running Kosmos (stock) with patches, if that matters.
  5. E

    Hacking NXDumpTool dump removal

    Hey! Looking to sell some of my game carts, as I don't play them anymore. I made xci dumps of the games (made using nxdumptool). Later found out carts can get banned, so i'm looking to remove these so the carts don't get banned for the new owner. Dumped: XCI with certs (split) Certs ExeFS...
  6. E

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Damn. Oh well, guessing the buttoncell with last a long time since the trinket is powered so shortly each time. Maybe possible to use the usb-c port as a power switch, so it doesn't need to manually be powered on/off each time?
  7. E

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    @mattytrog Working great now! Think it was a bad usb-c connection. Any way to power the trinket from usb-c plug on the switch? Using external buttoncell right now.
  8. E

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    @mattytrog Got it running via an external trinket connected to the switch with USB-C! However, to inject payload I have to press the reset button on the Trinket once. Is this normal?
  9. E

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Nevermind, got it working! Need to press the "reset" button on the trinket to get it to inject payload though, for some odd reason. No biggie.
  10. E

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Got a trinket setup with a 3v battery. Soldered a USB C to micro-usb cable, ONLY connecting the D- and D+ wires (leaving ground and power unconnected). Got trinket setup with dualboot and switchboot following...
  11. E

    Hardware Is my right joycon rail dead

    Ah ok! But new joycon worked, so I assume thats where the issue was :) High voltage likely due to nothing being plugged in?
  12. E

    Hardware Is my right joycon rail dead

    What? Why would I get a brick because of a high no-load voltage reading?
  13. E

    Hardware Is my right joycon rail dead

    It was the joy-con, new one worked! Why is it reading 7v instead of 5v though?
  14. E

    Hardware Is my right joycon rail dead

    Hey! My right joycon won't detect in connected mode. I've tried updating firmware on it, reseating the rail connector, etc etc. The plug to the ribbon cable is slightly messed upp (inside the joycon). I assumed this was the issue, but then I checked the voltage going to pin 4... It's at 6.9-7v...
  15. E

    Hacking SWITCH NOOB PARADISE - Ask questions here

    Oh, and a little thing: I ran an old guide for making nand backups. My switch crashed, and rebooted into OFW. I had the CFW files from https://gbatemp.net/threads/backup-restore-your-nand-get-your-biskeys-tseckeys-keys-txt-guide.513386/ on my sd card when it booted. Never ran CFW, and did not...
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    Psionic Roshambo @ Psionic Roshambo: https://www.youtube.com/watch?v=KYZD7ykz9aQ +1