Recent content by dibas

  1. D

    Need help identifying Switch OLED board components

    Just a quick update, I replaced the components with 3 nH inductors and everything works just fine, in case anyone else reads this later.
  2. D

    Need help identifying Switch OLED board components

    What confuses me is that the first letter looks like a μ for micro, but 3 μH would be way too high for a component of this size, correct?
  3. D

    Need help identifying Switch OLED board components

    Hey everyone, I removed a few components next to the left joy con FPC connector in my Switch OLED because of a botched repair. It looked like this before: And now, cleaned up with the components removed, it looks like this: Now, I know the following components are 0201 resistors: Can...
  4. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    I ordered a new set of 0201 100 Ohm resistors now, I guess that should be the correct one. I still have no clue on how I am going to remove the existing resistor with an iron though. I have a few good tips, but no hot air station, and with just a single tip I don't see the solder melting on...
  5. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    I have to correct myself, you were probably right. After searching for the problem and retesting everything I now think that this resistor is the problem. When measuring its resistance it mostly shows 100 kOhm and only sometimes 100 Ohm. I thought that maybe some more solder on the right side of...
  6. D

    Switch oled fan and left joycon charging not detecting

    Hi, I have got a very similar issue after installing a Picofly in a new OLED model. (see https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/page-825#post-10559278 and https://gbatemp.net/threads/picofly-a-hwfly-switch-modchip.622701/post-10560321 and...
  7. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    A quick update on my problem of the left joy con not being recognized after a Picofly installation anymore: I measured all the resistors of the left joy con IC shown in the quote above, the values match with what sthetix gives as correct resistance values as shown here...
  8. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    The right joy con works perfectly fine, it is just the left joy con that is not detected. I tried measuring the resistance but it was not measurable. My multimeter cables are huge though, so maybe I just didn't make good contact to the resistor ends. I will try it again. The other resistors all...
  9. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    I did that today, cleaned up everything, unfortunately it didn't solve the problem. This is how it looks like now: I will try reading the resistor values next to the left joy con's handshake IC next, my multimeter broke down for some reason, so as soon as I get a new one I will post whether...
  10. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks a lot, I had not seen that post before while searching for similar problems. I will check the IC. The connector looks fine to me. I still wonder whether the cause might be a damaged trace close to the APU shield though, because I did not really touch anything around the Joycon handshake...
  11. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi everyone, I just did my first Picofly mod on my OLED. The chip works just fine, but I noticed that the left joy-con is no longer being detected as connected by wire. It only connects using bluetooth now. The joy-con is shown as being charged when connected to the console though. I...
  12. D

    Homebrew The SD Card slot of my Wii U stopped working. Is there another way to access Homebrew?

    You're welcome. I don't want to promise anything, but I might have a look at it in the next few days. Will post here if I manage to get something done.
  13. D

    Homebrew The SD Card slot of my Wii U stopped working. Is there another way to access Homebrew?

    Wow, I'm sorry mate. That config downright sucks. A and B try to load an IOSU image from the SD card, that's why they get stuck on the loading screen (it's basically a please wait while IOSU is loading screen). So I'm actually not sure where to go from here. It's possible to overwrite the...
  14. D

    Homebrew The SD Card slot of my Wii U stopped working. Is there another way to access Homebrew?

    Yeah the configuration is installed inside the DS title. Maybe there is a copy of the config you used on your PC or you recognise the tutorial you used somewhere online? If not, I'm afraid you'll have to try every single button on the gamepad because afaik all of them can be mapped, and hope you...
  15. D

    Homebrew The SD Card slot of my Wii U stopped working. Is there another way to access Homebrew?

    I'm sorry if I didn't explain myself properly. It's exactly as @cruplezone says. The standard haxchi config returns the user to the system menu with signature patches installed, allowing you to launch the homebrew channel if installed separately before. If launching haxchi directly redirects...
See more