Recent content by Darkdialga6

  1. D

    Modded Switch oled battery 0% and cpu temperature 0°c

    I just forgot this mainboard because i can't fix it. I can't see any damaged traces. The one seller from germany sold me this motherboard as defective but had listed it as 'working' and 'used'. He did not want to take the motherboard back or give me a refund. I won't buy from this seller again...
  2. D

    Modded Switch oled battery 0% and cpu temperature 0°c

    Ok, thank you for the useful information. I have installed the picofly myself into the switch oled console. And i did not have soldered wires for Sda/Scl. I have also looked at the sda/scl resistors and they seems to be fine and have no bridges of course! I have also measured the sda/scl...
  3. D

    Modded Switch oled battery 0% and cpu temperature 0°c

    Ok, thank you for sharing this but the problem is that i couldn't see any damaged traces around the cpu and i find it also weird that the cpu temperature shows also 0. I also tried to reflow the cpu two times but it didn't change anything. Now i am unsure if i can fix this switch oled console...
  4. D

    Modded Switch oled battery 0% and cpu temperature 0°c

    Hello, can somebody help me please? On my fresh modded switch oled, all fuel gauge ic values are 0 and cpu temp shows also 0. I have already checked for a missing component and damaged traces but could not find anything. Does it only need a max17050 replacement? The console currently can not...
  5. D

    Nintendo switch can't be fully charged

    The 7th pin on my usb c port from left to right shows me the OL reading too but when i put a little pressure with the multimeter on the pin, it shows me a reading, so i know that the 7th pin is just bad soldered haha.
  6. D

    Nintendo switch can't be fully charged

    Thanks. Those diagrams are helpful. 👍 the OL reading is not normal, it should has a reading. (It is the 5th pin on the usb c port from left to right which shows me OL reading. And the 7th pin from left to right isn't well connected in my case.)
  7. D

    Nintendo switch can't be fully charged

    I checked the usb c port with a multimeter and i found a pin which has no good contact to the pad. And another one just has 'OL' reading. Maybe that's the problem and i only need to fix that. The other readings of the usb c port are ok. I could try to fix the one bad soldered pin with just a...
  8. D

    Nintendo switch can't be fully charged

    Hm, now this nintendo switch doesn't show any signs of charging anymore. I don't know what's wrong with it. xD
  9. D

    Nintendo switch can't be fully charged

    Yes, it is weird. The Bq24193 or M92t36 chip could need a replacement..
  10. D

    Nintendo switch can't be fully charged

    Thanks for the tip. I will order a new battery and then i will test it again. 👍 I have already replaced the usb c port on this console. Replacing the battery would be one of the easier repairs. 👍
  11. D

    Nintendo switch can't be fully charged

    Hi, thanks for your reply. Yes, it can boot normal to OFW and CFW. When plugged in a charger it shows this.
  12. D

    Nintendo switch can't be fully charged

    Hello, i have a problem with my nintendo switch. It can't be charged more than 30%. And in hekate, it shows under battery info that the temperature status is hot. What's the cause of this issue? And what can i do to fix it? Best regards
  13. D

    What will happen if one of those 5 lcd data lines on the switch lite has a solder bridge? Would there be an lcd issue or not?

    There is another picture of my modded beautiful switch lite console in green. 👍
  14. D

    What will happen if one of those 5 lcd data lines on the switch lite has a solder bridge? Would there be an lcd issue or not?

    Here is a picture of my modded switch lite. Everything is working and the lcd is working too and has no issues as you can see in the picture. 👍
  15. D

    What will happen if one of those 5 lcd data lines on the switch lite has a solder bridge? Would there be an lcd issue or not?

    Ok, thanks for the info. But if the lcd shows an image, there shouldn't be a solder bridge on those 5 lcd data lines, am i right? And i must say, yes the switch lite is hard to solder for a modchip install. The points are small and near together. Btw the modchip install was successful (i get...
See more