I removed flex cable for mosfets, It recognizes SD card in ofw Iwill try bare mosfet version tonight.Can you try another module? or try this module on another unit.
As i suspect the male conector in sdcard module is easier to get issue.
I removed flex cable for mosfets, It recognizes SD card in ofw Iwill try bare mosfet version tonight.Can you try another module? or try this module on another unit.
As i suspect the male conector in sdcard module is easier to get issue.
Thanks @Adran_Marit . This is interesting data and as of yesterday I was thinking maybe the pico isn't the best suited for the Lite. If my reball yields nothing significant. Then im going to call it done for me because its just too much headache to fix and I'm all out of ideas for it. Will probably get a new one and try a hwfly install. Even if it costs bit more than pico at least it'll work. Though for v1/v2/oled it's Pico all the way as I feel they're more suitable for it thus far. Thank you for the insightful dataHaven't checked yet as I've been busy, will probably check tomorrow morning
edit: So just checked, 7 responses.
So far the most common factors are;
If others wish to reply the survey is here
- Switch Lite - (57.1%)
- Rp2040-zero/one - (85.7%)
- Mosfet install - (71.4%)
- Dual Mosfet - (60%)
- Most Common Mosfet - IRFHS8342
- No SCA/SLC - (100%)
- Memory - Toshiba/skhynix (42.9%)
- 47Ohm Resistors - (71.4%)
- Blue Screen - (57.1%)
- Console worked before closing - (57.1%)
What ?, ive install >10 lites, no issue at all, single mosfet all. No victim unit yet. The most issue i had was only because human error and all is recoverable. Sure this picofly is suitable for lite model.Thanks @Adran_Marit . This is interesting data and as of yesterday I was thinking maybe the pico isn't the best suited for the Lite. If my reball yields nothing significant. Then im going to call it done for me because its just too much headache to fix and I'm all out of ideas for it. Will probably get a new one and try a hwfly install. Even if it costs bit more than pico at least it'll work. Though for v1/v2/oled it's Pico all the way as I feel they're more suitable for it thus far. Thank you for the insightful data
In my case, I did use a beta 2.72fw that had clk error. So could be that but there are a lot of people on here with Lite pico problems with more stable fw. Don't know what to say tbh.What ?, ive install >10 lites, no issue at all, single mosfet all. No victim unit yet. The most issue i had was only because human error and all is recoverable. Sure this picofly is suitable for lite model.
How does one go about fixing nand partitions?hi, maybe the picofly for lite is suitable for the soldering proficient. v1/v2 erista are more easier for me: i used the alternative pins (on the emmc board) and those are more separated…
as for my purple screen lite, i’ll send it to a repairshop. once the pico is installed, i can try to fix the nand partitions.
tonight i’ll work on a v2 erista.
I install on average 3 Picofly per day on all models, never a problem. If there is a problem it lies between the soldering iron and the switchWhat ?, ive install >10 lites, no issue at all, single mosfet all. No victim unit yet. The most issue i had was only because human error and all is recoverable. Sure this picofly is suitable for lite model.
if you can get it to glitch and accept payload there are tools for rebuilding itHow does one go about fixing nand partitions?
Ahhh, leaves me out then.if you can get it to glitch and accept payload there are tools for rebuilding it
Not to be anal, but (proceeds to be anal) v2 is Mariko, Erista is v1 unpatched and v1 patched.hi, maybe the picofly for lite is suitable for the soldering proficient. v1/v2 erista are more easier for me: i used the alternative pins (on the emmc board) and those are more separated…
as for my purple screen lite, i’ll send it to a repairshop. once the pico is installed, i can try to fix the nand partitions.
tonight i’ll work on a v2 erista.
Is it still turn on as now?my friend wants to ask besides here where else is there a Nintendo Oled CLK pin??
yes it's still onIs it still turn on as now?
now it doesn't turn onIs it still turn on as now?
yes it's still on
Post automatically merged:
now it doesn't turn on
Anda perlu memperbaiki jejak jika tidak jejak di bawah apu cukup banyak yang mati. Kami membutuhkan close up dari titik tersebut
Dikirim dari iPhone saya menggunakan Tapatalk
I bet with u the purple screen came because u had issue with the cmd resistor when u soldered to it u prob discinnected it from the bord when u installed the pico.Hello Everyone,
again a problem with PICOFLY and OLED installation
today i get again the Purple Screen with KERNEL PANIC installing Picofly with 2.74 firmware version..
Mod end fine, led code is correct, console boot in Hekate... but:
- if i enter in EMMC it says Fails to init EMMC
- if you try to start on OFW go in Purple kernel panic
- even if you remove the mod and try to start a clean switch the console go in kernel panic (purple screen)
If anyone got stuck in my situation there is a easy fix :
You just need to install an HWFLY and everything got FIXED without any issue (no kernel panic) and if you start the console after remove the mod it works perfectly
@rehius what can be? how can i help you to fix this issue on Picofly?
problem happen two times to me
one with skhynix EMMC and this time with Samsung EMMC
OLED model
i've Used a normal Picofly chip (RP2040 Zero first time) and now the new Aliexpress RP2040 Picofly
if i can provide any info to investigate the code i'm at your disposal
thanks
Upload a close up picture so we can see if its possible to fix or notPost automatically merged:
How to do it???
That’s true. Now the code is based on pulses like morse code.does the flash after usb write still have to be red? i flashed 2.74 but it flashes green with the rgb jumper set but when i flash 2.67 it flashes red? someone said the color flash doesnt matter, is that true?
Post automatically merged:
does the flash color still matter? i set the rgb jumper adn flashed 2.74 it still flashes green i flash 2.67 it flashes red?
@lightninjay right about nowdoes the flash after usb write still have to be red? i flashed 2.74 but it flashes green with the rgb jumper set but when i flash 2.67 it flashes red? someone said the color flash doesnt matter, is that true?
Post automatically merged:
does the flash color still matter? i set the rgb jumper adn flashed 2.74 it still flashes green i flash 2.67 it flashes red?