I've been using a paperclip jig for a while and I checked out my pins today and pin 1 looks "pressed in" compared to the rest. The joycon and everything still works fine but I'm worried how bad it would be if the pin stopped working and if I should get another console before the new hardware fix comes out.
My joycon rail is looking the same. After continuous insertion and removal of the paperclip jig, the rail will eventually be worn down to the point of no return. At that point you can just purchase a new rail and swap it out. If you want to keep yours though, just try and minimize its use
Pin 1 is GND, same as pin 2 and 7. So don't worry too much about it.
Source: https://reswitched.tech/hardware/joycon
Source: https://reswitched.tech/hardware/joycon
Pin 1 is actually a home button but is only used to access the Rcm mode. Pin 2 and 7 though are ground however. if you bridge pin 1 and 2 however it will only count as home button press if the joycon is inserted
The metal part with the five screws? Does it simply slide off when those five screws are out or do I have to open up the console?
Do you have a link please? I can't find it via search. Does Amazon sell them?
I'm not sure about amazon, but google how to remove the rail on switch, I'm sure there are all sorts of tuts out there
This is why I'm not a fan of using paperclips, the metal is pretty hard and abrasive.
Pin 10 is the home button, pin 1 is GND. Check your facts (or the link I provided as source).
I’m currently waiting for a new rail lol, although the joycon I used to bend pin 9 into 10 still works but my normal joy-con does not work because it’s flat and I can’t charge it
My apologies. I meant pin 10. I'm pretty intoxicated. I was thinking of the rails backwards
ifixit has a teardown video of the switch, you should be able to glean some info from it.
What? So you mean if I just make a small copper pads attached outside my joy-con it just need to be soldered to a single pin (pin 10) and then I just need to touch the copper pad and it enters RCM?
CAN A ELECTRONICS EXPERT PLZ REPORT IF THIS WOULD WORK?
Last edited by guily6669,
If you are implying that you can use your human body as the ground for pin 10. It will not work, or at least would be unreliable. It's hard to say for sure without 1) testing 2) knowing the input impedance and pull up value on pin 10. Though, in most normal designs where the pull up impedance is likely 10k or 100k it wouldn't work reliably as the human body is usually in the hundreds of kohms (mostly skin resistance) It's 10k or lower when pressed hard, sweaty or otherwise moist.
Personally I think the jigs are a very bad idea and people are likely to have pin connection problems with the joycon down the road as the pins are over stressed and the plating is damaged due to fretting and scratching by materials like steel (paper clip). The pins in the switch are likely beryllium copper, or phosphor bronze (both softish but springy) with a nickle followed by gold plating (hardish but still pretty soft). They aren't going to hold up super well over the medium term.
Similar threads
- No one is chatting at the moment.
-
-
-
-
-
-
-
-
-
@
BigOnYa:
He was the ass of gbatemp, everyone knocked on him, I honestly felt bad, even though I was guilty myself, but he egged it all on himself, -
-
-
@
BigOnYa:
I feel like gbatemp should make t-shirts or memorabilia to remember the lost ones. I bet the Polly shirts would sell out quick.
-
-
-
-
@
BigOnYa:
Your correct, Somebody would be guilty and there would be riots, then they storm the gbatemp capitol,
-
@
K3Nv2:
Online or not there are still certain rights that judges would have no issue handing out a warrant over -
-
@
BigOnYa:
Honestly I'm scared to, from you, but ok, lemme turn on vpn, virtual machine, private browser first
-
-
-
@
BigOnYa:
That robot is here somewhere, I hear it moving around at night, but I haven't seen it for months.
-
@
BigOnYa:
Oh that laptop I give to ancientboi, so you been watching him for months, and he's been watching you
-
-
