Whenever I turn on my switch I get a blue screen. I am a complete dumbass for doing this but I wish to know if there is a way to fix this issue or if my switch is bricked indefinitely. To start this shit show, I was trying to upgrade my sd card to a bigger sd card through atmosphere by following the re-entry guide for hekate (upgrading your micro-sd card). Around step 21 I got confused and couldn't find the emuMMC option (it was on the home screen I still can't believe I couldn't find it. I ended up choosing random options on the screen below and I clicked on the option eMMC USER (I got frustrated) and immediately turned off the console because I realize it wasn't doing what I wanted. Apparently it was writing on the consoles NAND and I ended up corrupting the console so badly, to the point where I cannot boot my switch without seeing this damned blue screen. I have tried completely powering down the console (Holding the power button until the console powers off) to no avail, I have tried booting into hekate (I'm using autoRCM) and TegraRCM isn't detecting an RCM device. I've tried backing up my console with the backup I had but I can't even boot into hekate to perform a full NAND back-up. Is there a fix for this or am I going to have to purchase a new switch.
Help Accidently blue screened my switch!!!
- Thread starter bladex987
- Start date
- Views 3,472
- Replies 37
- Joined
- Sep 2, 2020
- Messages
- 1,284
- Trophies
- 0
- Age
- 39
- Location
- TORONTO
- Website
- form.jotform.com
- XP
- 2,219
- Country
The picture shown is for backup nand not resore, so not likely writting anything to emmc though.
If you have a v1 unpatched device, and you have auto_RCM turned on, you could mostly inject payload after cold boot,or remove emmc module before boot and reconnect when you see device detected from PC.
NAND corrupted is not a big deal if you have your prod.key and prodinfo backup, you could always rebuild nand if you dont mind just losing savedata
You might have restored the emummc boot0/1 into sysnand IMO.
Boot your device into RCM mode(using jig or unplug emmc module before boot then plugin again). and resotre boot0/1 either from backup or emmchacgen. Make sure boot0//1 matches you device fuse count.
If you have a v1 unpatched device, and you have auto_RCM turned on, you could mostly inject payload after cold boot,or remove emmc module before boot and reconnect when you see device detected from PC.
NAND corrupted is not a big deal if you have your prod.key and prodinfo backup, you could always rebuild nand if you dont mind just losing savedata
Post automatically merged:
You might have restored the emummc boot0/1 into sysnand IMO.
Boot your device into RCM mode(using jig or unplug emmc module before boot then plugin again). and resotre boot0/1 either from backup or emmchacgen. Make sure boot0//1 matches you device fuse count.
Last edited by jkyoho,
Yes, I guess I'll have to use that
Post automatically merged:
wait how do I restore my nand if I can't even boot into hekate?
If I'm reading correctly, they took that screenshot BEFORE they started messing around and getting the blue screen.
No this is an image from the web
Post automatically merged:
I did, but it's not a screenshot from my switch.
- Joined
- Sep 2, 2020
- Messages
- 1,284
- Trophies
- 0
- Age
- 39
- Location
- TORONTO
- Website
- form.jotform.com
- XP
- 2,219
- Country
remove the screws and back cover+metal cover so that you can detach your emmc module
Hello, I am having this exact same problem, I had auto rcm on, but as soon as I connect the cable/turn on the console, the screen is blue. I did the mod long time ago and I can't find any backup (I don't even know what files I have to search). I used the tinfoil/paperclip method to mod it, so I got no chip or soldering stuff going on.
- Joined
- Sep 13, 2022
- Messages
- 7,276
- Trophies
- 3
- Location
- The Wired
- Website
- m4x1mumrez87.neocities.org
- XP
- 22,332
- Country
I always suggest making a backup through Hekake, otherwise you have no way of restoring. Its also best if you want to boot from an emuNAND to play all of your offline games and homebrew.
NEVER use tinfoil to bridge the contacts on the JoyCon connector, as you can potentially fry it. Buy those jigs off eBay or AliExpress as they cost pennies and are more easier to use.
I have some backup data, but I got no clue if it's helpful or not. What exactly I need to look for?
oh, ok. I got them. I used them, but then it wouldn't run anything, not even stock. So
I had the dumb idea to turn it on without the sd card. Now it's stuck on blue screen and can't even access to rcm
If you restore your nand and it still wouldn't boot there is something wrong with your switch.
Similar threads
-
AncientBoi
-
K3Nv2
-
BigOnYa
-
Xdqwerty
what are you looking at?
-
-
@
Xdqwerty:
@BigOnYa, I think that listening to the same 15 songs on the music player in my dad's car all the time made me kind of hate "normal" music.+1
-
-
-
-
-
-
-
-
-
@
BigOnYa:
I seen a bunny rabbit get swept up and taken by a hawk yesterday in my back yard, it left a bunch of rabbit hair in grass. Wild to see it fly off carrying a rabbit.
-
-
-
-
-
-
-
-
-
-
@
BigOnYa:
The other night was watching tv in my screened in porch, and heard something walking on my porch roof, thought maybe it was a raccoon, so I grabbed my rifle and went out to look, it was just a duck, lol+1
-
-
-
-
]