when downgrading my old3ds japan emunand to 2.10 i have error, so i must restore my emunand. can you tell me how to fix this?
thanks
After updating my sysnand to 9.2 same error appears, but this time it's 0004001000022400.cia
I don't use GW at all. New fresh emunand9.Are you still trying to do this through your GW?
0004009B00010402.cia
fsException:
fs.cpp:117: Result: 0xD9004588
failed to write file!
Did you store the update files in '/updates'?
i know how to restore emunand. but what i mean on my post is how to downgrade emunand to 2.1.0 without error..Open Decrypt9 -> EmuNAND Option -> EmuNAND Restore ->Enter the Code -> Select Your Backup ->Wait for Install to Finish.
So just to follow up, I dont think its possible to just jump into the guide at https://github.com/Plailect/Guide/wiki/Part-4-(Getting-the-OTP) starting from 9.0 sysnand and CFW/GW emunand. I used the same N3DSXL same SDCard starting the guide from Part 3 using Emunand9 and was succesful. So in conclusion, I am not quite sure what the issue is, but you cant just jump into the guide at Part 4 like it says to, if you're starting from 9.0.x Sysnand and previously installed CFW/GateWay Emunand you should likely start from Part 3 and save yourself many hours of fucking around.i know how to restore emunand. but what i mean on my post is how to downgrade emunand to 2.1.0 without error..
thanks..
i follow the guide from part-1 until part-4 without jump any part and i stuck when downgrade emunand to 2.1.0. but finally i can downgrade my emunand and get my otp (part-4 end)So just to follow up, I dont think its possible to just jump into the guide at https://github.com/Plailect/Guide/wiki/Part-4-(Getting-the-OTP) starting from 9.0 sysnand and CFW/GW emunand. I used the same N3DSXL same SDCard starting the guide from Part 3 using Emunand9 and was succesful. So in conclusion, I am not quite sure what the issue is, but you cant just jump into the guide at Part 4 like it says to, if you're starting from 9.0.x Sysnand and previously installed CFW/GateWay Emunand you should likely start from Part 3 and save yourself many hours of fucking around.
You can, though eShop will most likely not work.i follow the guide from part-1 until part-4 without jump any part and i stuck when downgrade emunand to 2.1.0. but finally i can downgrade my emunand and get my otp (part-4 end)
i'll wait to go to part-5 until someone confirm i can switch my emunand region on cfw permanent
thanks..
i know eshop wont work if i change region.You can, though eShop will most likely not work.
Once you finish Plailect's guide it is safe to change your regioni know eshop wont work if i change region.
can you give me tutorial change region on a9lh? i follow plailect guide but it must same region..
thanks
so i follow part-5 install a9lh install cfw and at the end change region, right?Once you finish Plailect's guide it is safe to change your region
I prefer AuReiNAND, as its more mature with its implementation of a9lh. It's up to you which one you use however.so i follow part-5 install a9lh install cfw and at the end change region, right?
i already have backup of 'changed emunand'
can i restore it or i must start changed emunand from the beginning?
its better use cakes or aureinand cfw?
thanks for your answer..
thanks, i will try it.. if i have problem can i ask you again?I prefer AuReiNAND, as its more mature with its implementation of a9lh. It's up to you which one you use however.
If you restore the backup of changed emunand, it will remove a9lh and you will be stuck without a9lh.
However, you can restore the changed emunand to an emunand on your SD card (create one with EmuNAND9 if you already removed it), then dump the CTRNAND partition, TWL partitions, and the AGBSAVES partition and restore those to your SysNAND.
No problem! If you have any problems feel free to askthanks, i will try it.. if i have problem can i ask you again?
thanks again..