Recent content by ojobenito

  1. O

    Picofly AIO Thread

    Quick question. Is there any alternate 3.3v/vcc point for the V1/V2 Switch? I REALLY hate that point next to the ram modules on the diagram. There is a capacitor nearby that I accidentally bridged a couple of times and it takes ages to fix and get rid of the solder bridge. So, any valid and...
  2. O

    Picofly AIO Thread

    Patched V1 Erista. I had this same errores (not the emmc slow mode, but it didn't boot). I tried to add that resistor and now everything is working again. I've been days trying to diagnose what was happening, and it was just this easy fix. Thanks a lot!
  3. O

    Picofly AIO Thread

    Nintendo Logo, then Black Screen, and it hangs there. No Orange Screen after waiting about 30 seconds or so. What's weird is that with no chip installed, the console didn't boot (I think), but official recovery mode did boot, and I did a reset (keeping saves), and then an update, and then, the...
  4. O

    Picofly AIO Thread

    Hi. Some time ago I had a problem with a V1 Switch that had the Orange Screen error after installing Picofly. If I launched atmosphere, it displayed the 2 Atmosphere screens (text and logo), and then Black Screen, and after some seconds, Orange Screen. If I booted System Firmware bypassing...
  5. O

    Picofly AIO Thread

    Hi. I made a Picofly installation today on a V1 patched. I've made 4 or 5 picofly installations before with no problems. I always use the proper flex cable for cpu points, enamel wire for board pads, and a plastic insulated thin awg wire for VCC and GND. But after installing this one, the...
  6. O

    Picofly AIO Thread

    Yes, I know all GND on the device is connected. What I'm saying is that I bridged that capacitor for the GND point to the one that is on its right. There are 3 of these capacitors together. I was just saying if all 3 are connected together and my accidental bridge doesn't matter.
  7. O

    Picofly AIO Thread

    Hi. Quick question. I accidentaly made a bridge on the capacitor for the GND point on a V1 Erista Patched that I can't easily fix. Next to that capacitor for the GND point are 2 more capacitors. Are all connected to GND and the bridge doesn't matter? I uploaded the image of the board and to the...
  8. O

    Picofly AIO Thread

    Then no direct Fusee loading on V1 unpatched? Is there any way to auto-load a payload under Hekate? (not interested at all on auto-rcm, by the way) Thanks for all your help.
  9. O

    Picofly AIO Thread

    It looks the emmc is not "slow", but a regular one (screenshot attached) Yes, I've tried that and it works and loads Atmosphere with no problem. I don't know what can be causing the issue of not loading Atmosphere directly when booting, but Hekate loads (and Atmosphere loading from Hekate...
  10. O

    Picofly AIO Thread

    I got 3v3 from the capacitor to the right of the RAM modules, as shown in the PDF Picofly guide that is uploaded on this forum. Hekate does indeed load with no problems when put on the MicroSD card root folder renamed to payload.bin In summary: - Console is V1 Erista patched updated to last...
  11. O

    Picofly AIO Thread

    Hi. I made my 1st picofly install. (Fw 2.73 as 2.74 was scrubbed it seems) When I tested it after installation, I got the "No SD Card" logo on the switch. So, I put a MicroSD card, FAT32 (as I always do with jig switches), with the atmosphere payload (fusee.bin) renamed to payload.bin located at...
  12. O

    Picofly AIO Thread

    I will use a hwfly flex cable for mosfets (it's much more of a headache the mosfets installation than the $10 that the flex cable costs) About the cable, I think the plastic cover is 0,58mm, but the cable itself inside the cover is about 0'2mm. It's just like a hair, but a little bit sturdier...
  13. O

    Picofly AIO Thread

    Ok. Time to start my picofly installation. Just a quick question. I see a lot of people uses enamel thin wire (the one that is almost like a hair, similar [or maybe the same] used in coils). Is it mandatory to use that kind of wire? I have it, but I don't like working with that. I also have a...
  14. O

    Picofly AIO Thread

    Ok, I will do the nand backup. Is pocofly more dangerous than V1 rcm method and that's why you recommend making the nand backup? I never did nand backup on my other switch because I never did emunand, nor I touched any systen files, overclock, or any mods/overclock/anything. I always use a...
  15. O

    Picofly AIO Thread

    Hi. I might be doing a PicoFly installation this weekend. I don't see much information about MicroSD preparation. I'm in no way interested in emunand (please avoid replies saying "it's essy and you should do it", I really don't want emunand), so how can I boot directly into Atmosphere and that's...
See more
General chit-chat
Help Users
    AncientBoi @ AncientBoi: Chips Ahoy cookies :D:wub::D