But if he only boots Nintendont from a USBLoader it should keep the settings no?whatever usb loader your using is changing the settings probably
But if he only boots Nintendont from a USBLoader it should keep the settings no?whatever usb loader your using is changing the settings probably
You said you were using a single drive, but looking at the screenshot you provided, it seems you are using both an SD and USB. Copy the controllers folder over to your USB drive.without a controller.ini file HID test shows the PID as 0268 and ViD 054C
I have the same problem, Just use an older Rev like the 2.223 until the devs resolves this issue
But if he only boots Nintendont from a USBLoader it should keep the settings no?
I'm unsure to be honest. I know I ran the updater in USB Loader GX itself a couple weeks ago and it came back as being up-to-date.Not sure how cyan has it set up. Are you using the one in his signature?
well the sd is only for program, i read that if you use a nonpowered usb you need to use the bottom back port for the controller. so i tried unplugging the power from the y splitter and it actually loaded the controller. but crashed my wii.. so i think imma try to install a game on the SD cardYou said you were using a single drive, but looking at the screenshot you provided, it seems you are using both an SD and USB. Copy the controllers folder over to your USB drive.
Just do what I told you to do, and start answering questions correctly. You are using two drives, one for Nintendont and one for games. The controller.ini file is read from the same drive that you launch games from.well the sd is only for program, i read that if you use a nonpowered usb you need to use the bottom back port for the controller. so i tried unplugging the power from the y splitter and it actually loaded the controller. but crashed my wii.. so i think imma try to install a game on the SD card
using a Y splitter is almost impossible for nintendont compared to wii loaders =/
I think that you are using an old version of CFG try using USBLoader GX from Cyan signature and post the results! Remember to turn on HID settings in the loader.I know it is frowned upon here and I am awaiting to be told to "read the thread" but at over 1000 pages, cut me some slack.
I am new to the USBLoaders game and, thankfully, have everything set up for the most part. But I need a little bit of advice.
I am running in my vWii
Nintendon't
CFG USB Loader
Official Gamecube Adapter
The problem lies with the Gamecube adapter.
If i run Nintendon't natively, I see it load the USB-HID controller and the controllers work fine. However, when I load the same game through CFG, I see Nintendon't load just the Bluetooth HID controllers leaving the Gamecube adapter dead.
The only options I saw in CFG were to set PAD Hook, which is on by default.
Any idea of how to force it to load the USB-HID?
Yup, you can use it, I don't remember the steps. I think that you have to synchronize it in the System Menu and then load Nintendont, or synchronize it in nintendont itself. Buy yes you can use it in a Wii/vWiican you use the wii u pro controller in nintendont on the original wii? or is it vwii only?
Just do what I told you to do, and start answering questions correctly. You are using two drives, one for Nintendont and one for games. The controller.ini file is read from the same drive that you launch games from.
I just picked up the latest version cfgv70r78 from here http://homebrew.svalas.net/cfg-loader-mod/ since i am using UStealth.I think that you are using an old version of CFG try using USBLoader GX from Cyan signature and post the results! Remember to turn on HID settings in the loader.
Same results?I just picked up the latest version cfgv70r78 from here http://homebrew.svalas.net/cfg-loader-mod/ since i am using UStealth.
It is what I had from the start. Just loads the Bluetooth HID by default and I cannot find a way to change it to USB-HIDSame results?
In cfg did you set "Alt Button Cfg" to ON?I know it is frowned upon here and I am awaiting to be told to "read the thread" but at over 1000 pages, cut me some slack.
I am new to the USBLoaders game and, thankfully, have everything set up for the most part. But I need a little bit of advice.
I am running in my vWii
Nintendon't
CFG USB Loader
Official Gamecube Adapter
The problem lies with the Gamecube adapter.
If i run Nintendon't natively, I see it load the USB-HID controller and the controllers work fine. However, when I load the same game through CFG, I see Nintendon't load just the Bluetooth HID controllers leaving the Gamecube adapter dead.
The only options I saw in CFG were to set PAD Hook, which is on by default.
Any idea of how to force it to load the USB-HID?