A friend sent these to me. I only tested the adapter on an old HWFLY modchip and its giving me conflicting results. I'm still waiting for my batch of rp2040 tiny to arrive tomorrow or after tomorrow to fully test on a fresh console.
That actually wouldn't matter since the other adapter I made works just fine. The only difference is that this one takes a little longer path. I only connected D0 for diagnostic purpose since I already have the other points soldered in. On this console it boots directly to OFW indicating something is wrong. The reballed eMMC is definitely correct otherwise it wouldn't have booted or at least wouldn't beep on both ends. I will test again with another fresh console once my chips arrives. I honestly don't see why it shouldn't.
Guys I did my first Switch Lite install with the trusty mosfet on the back.
However the glitch is quite slow, rarely taking less than 10 seconds.
Should I go for a double mosfet on the front or just accept that some Lites can be like this? (I hope for the second, lol)
I had an oled that glitched really slowly. anything between 10 seconds to a minute. mosfet on the back. Added another mosfet on the back - no change. Added a mosfet on the apu (so 3 mosfets in total) - still no change. disconnected mosfets on the back and only used the one on apu - boom, 3 second glitch every time.
most other oleds I've done have one on the back and glitch fast every time.
The point of the anecdote is that changing things around can make a difference in unexpected ways.
Guys I did my first Switch Lite install with the trusty mosfet on the back.
However the glitch is quite slow, rarely taking less than 10 seconds.
Should I go for a double mosfet on the front or just accept that some Lites can be like this? (I hope for the second, lol)
Welcome to the dark side of front mount mosfets my brother in arms .
what awg of wire did you use from the mosfet to the cap? From experience ,in this scenario, when i was using 40 awg wire the glitch was quite slow. When i moved to 30 awg it got faster. Its usually around 5-7 seconds glitch, but sometimes it takes 15 seconds. Do keep in mind that the soldering skills also affect the connections and therefore the glitch time.
share some light on me. I succesfully reballed 2 OLEDS (first time doing this,permanent dat0) but they broke (one in 1 month, the other one in 1 week). The 1 week one was fixed with a reflow, but the 1 month one was not fixed with a reflow -i think this one needs a reball.
I dont know what could ve went wrong tbh. I heat the board gradually for 4 minutes untill i reach melting solder temperature. After the chip sat in place, i leave the heat on for 30 more seconds . Then i take the heat off and let it cool.
But im clearly doing something wrong since im having this problem on both consoles.
Ok so. I checked picofly version and i was still on 2.73. I tryed several times more to update, and it finnaly worked.
After attempting to do a new NAND write from scratch with prodinfo, OFW was stuck on logo . So i did a NAND restore to my old NAND save (the one that i was getting 3539 error on ).
Now when trying to start OFW i get this screen View attachment 398276
Well. View attachment 398280
I encountered the same problem after installing picofly, I recreated mmc from the donor nand file. Just remember to write a higher version than your ofw software version
I encountered the same problem after installing picofly, I recreated mmc from the donor nand file. Just remember to write a higher version than your ofw software version
i did a donor nand rebuild . Worked for a couple of days, then it started acting up again.
While acting up i put 200 ohm resistor on DAT0 and 200 ohm on CMD, and i was able to boot OFW with no nand rebuild.
After that i did a Nand rebuild again and its been a couple of days "stress" testing it and so far its ok. But i dont know if this will last.
Oh nevermind im talking about 3539 errors,bootloops and blackscreens on startup. Your experience is probably just a bad HOS on OFW. I just realised.
Welcome to the dark side of front mount mosfets my brother in arms .
what awg of wire did you use from the mosfet to the cap? From experience ,in this scenario, when i was using 40 awg wire the glitch was quite slow. When i moved to 30 awg it got faster. Its usually around 5-7 seconds glitch, but sometimes it takes 15 seconds. Do keep in mind that the soldering skills also affect the connections and therefore the glitch time.
Post automatically merged:
share some light on me. I succesfully reballed 2 OLEDS (first time doing this,permanent dat0) but they broke (one in 1 month, the other one in 1 week). The 1 week one was fixed with a reflow, but the 1 month one was not fixed with a reflow -i think this one needs a reball.
I dont know what could ve went wrong tbh. I heat the board gradually for 4 minutes untill i reach melting solder temperature. After the chip sat in place, i leave the heat on for 30 more seconds . Then i take the heat off and let it cool.
But im clearly doing something wrong since im having this problem on both consoles.
I don't know what technique you use but this is how professionals do it,
After you lift the chip you should apply low melt solder (183C) to the pads of both chip and pcb before you wick it, this way you guarantee you left no solder behind that could potentially compromise your joints.
After you apply the paste and formed your balls, remove your stencil and apply heat 2 times with flux.
Hey, today I received a console back to which I had installed a picofly. It wouldn't boot, just black screen.
An oled, with DAT0 reball. It had the right absorptions in the charge, and after a quick look without finding any anomalies on the soldering, I carried out a reflow of the nand, without adding flux (I was sure that the old flux residue was still there), In fact it immediately flowed out of the nand.
The console started working again immediately.
I have never needed to reball to reactivate a console, I think it is due to the flux that creates "impedance" between the tin spheres of the emmc (even if it is sold as lead free). Do you confirm?
Or is it due to some impact?
How do you clean the flux from the emmc?
Hey, today I received a console back to which I had installed a picofly. It wouldn't boot, just black screen.
An oled, with DAT0 reball. It had the right absorptions in the charge, and after a quick look without finding any anomalies on the soldering, I carried out a reflow of the nand, without adding flux (I was sure that the old flux residue was still there), In fact it immediately flowed out of the nand.
The console started working again immediately.
I have never needed to reball to reactivate a console, I think it is due to the flux that creates "impedance" between the tin spheres of the emmc (even if it is sold as lead free). Do you confirm?
Or is it due to some impact?
How do you clean the flux from the emmc?
Quite frankly your issue is no different than the ones suffering from D0 adapters.
Just use good flux and make sure you clean after with solvent.
Use an ultrasonic if you want a squeaky clean for hard to reach spaces.
Managed to install a Picofly to an OLED with the provided FPGB. It works, but I'm currently running into the weirdest issue where with the backplate installed, it just boots into OFW but stuck at black screen, forcing me to remove the back plate, the shielding, and pull the battery and attach it back, and then it boots to Hekate again. Its gotten to the point where I just screwed only 2 of the metal shielding screws because I'm tired of unscrewing the thing.
Hi everyone, I'm getting a eMMC write error and the switch boots to OFW, what could be wrong? I checked the soldered points and I measure 0.8V (hope I used the tester well lol), what else could it be?
From the Picofly AIO guide PDF, my error is " =*=* eMMC write failure - write failed ", I get blue light, then 1 short yellow, 1 long yellow and 1 short yellow again. The yellow lights sequence repeat 2-3 times.
The kit is a Hwfly V5 I ordered from the official Hwfly store on Aliexpress a while ago, now it's apparently de-listed.
with my ns lite, I ripped off the clk pad, I accidentally removed a resistor on the side, I restored the pad, I put a resistor in its place, I started getting a blue screen, now I installed the pico fly with resistor 47, it still gives a blue or black screen, I found one I put a 100 resistor on dat0, and I had a non-SD screen, for a moment, I'm going to find another 2 100 resistors and change them... I believe it will work.
with my ns lite, I ripped off the clk pad, I accidentally removed a resistor on the side, I restored the pad, I put a resistor in its place, I started getting a blue screen, now I installed the pico fly with resistor 47, it still gives a blue or black screen, I found one I put a 100 resistor on dat0, and I had a non-SD screen, for a moment, I'm going to find another 2 100 resistors and change them... I believe it will work.
The nosd screen doesn't really mean anything, just that the CPU has done the glitch. First start hekate, then emmc info and see if everything is detected correctly then a stock boot, if everything goes then everything works
It's been a while since Microsoft released the Xbox One, and despite its age, there haven't been any reliable softmod methods to hack the console. Until now. A post...
After several months of work, the Harbour Masters 64 team have released their first public build of 2Ship2Harkinian, a feature-rich Majora's Mask PC port. This comes...
With the vast success of Super Mario Maker and its Switch sequel Super Mario Maker 2, Nintendo fans have long been calling for "Maker" titles for other iconic genres...
Palmer Luckey is known for his pursuits into the world of virtual reality, having founded Oculus and designed the Rift VR headset. Prior to the $2 billion dollar...
Another day, another Nintendo DMCA takedown against fan-made content.
Just a few minutes ago, Nintendo issued a DMCA takedown notice against a widely known and...
After a little more than three years of exclusivity with the Epic Games Store, Square Enix has decided to bring their beloved Kingdom Hearts franchise to Steam. The...
The complete source code for the Super Nintendo Entertainment System (SNES) version of Doom has been released on archive.org. Although some of the code was partially...
Sony is once more attempting to reintroduce players to their older library of games by re-releasing classic PlayStation 2 titles onto the PlayStation Store. During...
Skyward Sword is a divisive title in the Zelda series. Hailed with praise at launch with a 93 Metacritic average, the game since received criticism for the...
The latest State of Play is here. This is PlayStation's Summer showcase, providing updates to new updates on upcoming games and brand new reveals. The 35-minute...
Palmer Luckey is known for his pursuits into the world of virtual reality, having founded Oculus and designed the Rift VR headset. Prior to the $2 billion dollar...
It's been a while since Microsoft released the Xbox One, and despite its age, there haven't been any reliable softmod methods to hack the console. Until now. A post...
After several months of work, the Harbour Masters 64 team have released their first public build of 2Ship2Harkinian, a feature-rich Majora's Mask PC port. This comes...
Another day, another Nintendo DMCA takedown against fan-made content.
Just a few minutes ago, Nintendo issued a DMCA takedown notice against a widely known and...
After a little more than three years of exclusivity with the Epic Games Store, Square Enix has decided to bring their beloved Kingdom Hearts franchise to Steam. The...
Nintendo have officially announced a Nintendo Direct for tomorrow, June 18th.
The show will focus on Switch titles releasing this year and they have explicitly...
That's right! It's time for the Summer showcase you've all been waiting for. A Nintendo Direct is about to air, bringing us 40 minutes of Nintendo Switch content. The...
Sony is once more attempting to reintroduce players to their older library of games by re-releasing classic PlayStation 2 titles onto the PlayStation Store. During...
With the vast success of Super Mario Maker and its Switch sequel Super Mario Maker 2, Nintendo fans have long been calling for "Maker" titles for other iconic genres...
The latest State of Play is here. This is PlayStation's Summer showcase, providing updates to new updates on upcoming games and brand new reveals. The 35-minute...
The commercial, a transexual person walks into the club, techno music is playing loudly. The trans person pulls out a Nintendo switch, turns around revealing that their clothes are mens on one side and women's clothes on the other. "Don't fear the Switch"