Search results

  1. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    I can try that, do you know what pin goes into the left filter? Pin 21 or 22
  2. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    there’s no reading on both the top and bottom for the left. It did seem like it’s missing some solder but I checked and it was soldered down 1743307406 I will add some more solder and try to reflow it. Both the left top and bottom are OL. There is continuity from the port to the bottom left leg...
  3. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    I’m getting .75 on both 21 and 22! 🥲 1743215676 Seems like the chip is fine 1743216142 It’s the filters on the left side only the right side are seeing .7. 😭
  4. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    The left side (usb c south facing) of the filters are OL, the right ones read .7
  5. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    How would I check them? Red on ground and black on every pin of the choke?
  6. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    I replaced that choke and it still is OL, unfortunately do you know what else?
  7. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    Oh then yes the pins that go into SUSB1 and SUB2 is my assumption. Sorry these letters are confusing me a little. 1743107461 From the diagram I have 17 OL other readings are consistent with the video
  8. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    Based your diagram a5 (17) is OL! I checked again and (b5) 8 isn’t OL. 1743103686 Could it be the p13? There is continuity from a5 to the choke but OL. I replaced the choke already and same thing
  9. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    So I replaced the choke, with one from a donor and it’s still OL on 17 and 8. Do you know what else I should do? There continuity from that point to the choke still
  10. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    Yep with the breakout board. It showed continuity to all point that you mentioned. 1742354688 I checked and there is an ol on number 17/8 if flipped - all other points check out according to the video. Looks to be the choke filter on the back of the board. I’ll replace that piece off my donor...
  11. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    So I just did a check in continuity mode and they’re all good according to the schematic. Anything else to check for?
  12. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    Ok I don’t have one of those usb c output checkers. If I don’t have one would I still be able to check?
  13. dangbawu

    Switch OLED strange issue with usb functionality after mod install

    Just wondering, when you say desoldered, was it off before you took that pic? Because it’s still on there. Or has the filter just shorted when you checked. Thank you
  14. dangbawu

    Switch oled USB C port replaced. Charging works both ways but doesn’t dock.

    When docked the green light pops up on the dock but doesn’t port to tv. I tried with another switch and the dock works. Any ideas? Charging works both ways so I’m assuming everything was soldered properly. I tried measuring the p13 for faults but didn’t find no shorts or problems with the...
  15. dangbawu

    switch lite BSOD after picofly? Bottom Ram Chip shorted/gets very hot

    Thanks for your response, to further check, where is the gnd/vcc line on the lite? This is my first time working on one so sorry about my inexperience. Do you have places where I could potentially check for recommendations
  16. dangbawu

    switch lite BSOD after picofly? Bottom Ram Chip shorted/gets very hot

    Honestly not too sure what happened. I know the ram chip is shorted but how did that even happen. :/ any fixes or solutions? 1741495704 Perhaps when I was screwing in the heat pipe, it caused flex on the board due to the fact that the picofly chip gets in the way of it sitting flush? That...
  17. dangbawu

    Switch digitizer doesn’t work and stuck in headphone mode.

    Swapped the game card reader with 5 different ones and all the same result, game cards do read and play. I got this switch broken, and it previously had a mod failed attempt with a missing APU capacitor (was getting error 2002-2629 when I tried to read a game). I replaced the APU capacitor...
  18. dangbawu

    Moving files from modded switch to oled?

    Yeah just to update. THIS WORKED. If you have your original prod.keys and emummc backup (raw). Then you can get this to work. If you, like me, have split rawfiles from your backup. You need to compile the 15 rawnand.bin.00,rawnand.bin.01 e.t.c together to get a single rawnand.bin to make it...
  19. dangbawu

    Moving files from modded switch to oled?

    youre the best.
  20. dangbawu

    Moving files from modded switch to oled?

    I think i do actually. Theres a folder on my sd card called emuMMC/RAW1/Nintendo/save. Could I just copy and paste this /save/ folder over? There is also a emuMMC/RAW1/Nintendo/contents folder which i'm assuming are my games. Could I also just move this file over? For file decryption, I have my...