Search results

  1. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yup!! If I disconnect the cmd from Picofly I get the correct error "cmd isn't connected". If I measure from the top side of cmd resistor till the end of my wire, I get 4.7 KOhm I get *== only when I disconnect clk and CPU, I've checked again both wires and diode readings, everything is normal...
  2. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    On switch OLED I'm getting everytime the same error *== "No eMMC CMD1 request (poor wiring, or dead CPU)" does anyone has any clue what it could be?? Here is what I've checked until now: 1. All the wiring, they're soldered properly (I'm using the same wire that I've already used in the past...
  3. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yesterday I've watched a vid on YT, where the dude was saying most of the time, the caps are used in electronic as filter, to reduce the noise... So my question is, could I use caps on picofly instead of the 47 ohm resistors?? I am guessing that the resistors are used also to reduce noise, since...
  4. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Have you Have you tried with sda/scl?? The problem could be caused by long wire or also the glue from kapton tape
  5. Myst0gan

    Installing Atmosphere with a broken screen

    According to ctcaer here --> https://github.com/CTCaer/hekate/issues/898 It's possible, I just don't understand what he's saying and how to do that
  6. Myst0gan

    Installing Atmosphere with a broken screen

    I need to create emummc first, without it Autoboot won't work
  7. Myst0gan

    Installing Atmosphere with a broken screen

    How did you solved it?? I've got a modded oled with broken screen, so I can't create emummc normale a backup of the nand or the keys, since hekate doesn't support docking mode
  8. Myst0gan

    Switch OLED Screen not working after picofly

    I doubt that, if the battery were connected, the display will be the first one to say goodbye (electronic repair school on yt has an old video explaining why, he does it with a laptop screen). Which diagrams?? I still think that a trace is broken or some missing resistor 🤔
  9. Myst0gan

    Hacking Booting to hekate without eMMC?

    Impressive 👏🏽 can you make a guide?? Pdf with pictures or video. How did you figure out that emmc was completely dead?? Where have you measured 1,8V? 1705522211 How did you do that?? I'm asking just because of curiosity
  10. Myst0gan

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I believe that you've already answered to yourself. OLED is better, but 99% of people buy it because of the display, it's beautiful when you play in handheld mode. Since you are also considering a V2, I'm guessing OLED display isn't your case... So, why would you complicate everything buy buying...
  11. Myst0gan

    Switch OLED Screen not working after picofly

    Have you checked front and back of the board, if anything is missing or for broken connection??
  12. Myst0gan

    Switch OLED Screen not working after picofly

    Well... If you knock off the 47k resistor near the cmd one, the screen turns purple, so I would start looking in that area (if the connector and flex cable are fine), if a connection or components are missing. Most of the components in that area should be related to the screen.
  13. Myst0gan

    Hacking SWITCH NOOB PARADISE - Ask questions here

    If I'm not mistaken, fat32 is limited to 4gb files. Use gold leaf or tinfoil to install them from pc directly to sd card. Be aware though, people says that tinfoil gets you banned, personally I haven't experienced nothing like that, since I keep everything offline
  14. Myst0gan

    Hacking Hardware Repair shops in Berlin/Brandenburg (or somewhere I can ship the console) who offer patched Switch hacking?

    That depends on your economic situation, I can talk only for myself, I can mod my own console, so I'm good. You wanted to find someone who could mod your console, I told you where to find them. If I were you, I'd contact them asap before Nintendo starts reporting the ads, like they're doing with...
  15. Myst0gan

    Switch Oled unresponsive after woopsie with Picofly

    The chip will always start as long as it gets 3,3V and the ground is connected. If you're lucky, you blew up bq, m92 or pusb chip. Check the main power rail and if the console charges correctly (15V). Try board repair videos on YT, at least they can guide you through. I would recommend to check...
  16. Myst0gan

    Hacking Hardware Repair shops in Berlin/Brandenburg (or somewhere I can ship the console) who offer patched Switch hacking?

    Well... I found this one, but it's in US. If you change the settings to worldwide, you can also see offers from UK, France, Germany and so on... Look also on picofly thread in this forum, few weeks ago (if I remember correctly) a guy was talking about an installer from France. About the guide...
  17. Myst0gan

    Hacking Hardware Repair shops in Berlin/Brandenburg (or somewhere I can ship the console) who offer patched Switch hacking?

    Try on local ebay or Craigslist... Or ask directly to local repair shops, if they install switch mods. There are plenty of tutorials on YT
  18. Myst0gan

    OLED Switch Joycon not connecting when docked. What is damaged?

    Probably this is the solution https://gbatemp.net/threads/switch-oled-wont-detect-right-joy-con-after-installing-picofly.645161/#post-10323984 1705429703 Check the flex, rail and the connector, if they're all good, then check the area that @BigOnYa pointed out, if those are all good, then it...
  19. Myst0gan

    Hacking SWITCH NOOB PARADISE - Ask questions here

    From what I know, when you make a new emunanad, it copies bit by bit from sys, so in theory everything should be still there. Make a backup of everything and the keys before you try anything
  20. Myst0gan

    Picofly AIO Thread

    Yes, now it's one color but blinking frequencies are different, check the guide, it's all there
General chit-chat
Help Users
  • No one is chatting at the moment.
    K3Nv2 @ K3Nv2: https://youtu.be/PRMX5mX-hvs?si=JdjNrndYJ7PelC7q