Search results

  1. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    The resistor on the switch Motherboard where you solder the CMD point.
  2. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Very well done, specially the clk point and the kamikaze. Does anyone knows what tip was he using for drill?? It’s sharp has a needle :)
  3. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Just like impeeza said, they both are GRD layers.
  4. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yes, they are. Only GRD and VCC are masked. Just strip it a little bit and you get the pad to solder it. If you use a multimeter in diode mode you would find it by yourself easy.
  5. Viktorsilva

    Hacking Hardware Switch OLED SkHynix with Picofly long boot-time

    I had always chose for the single MOSFET directly on APU. The results are almost always instant boots.
  6. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Those chips are all clones from each other. I’m pretty shure the pins are the same. 1723120564 Yes, you can use the CPU Flex from the V2 on Oled without any problem. I personally prefer tor use single mosfet directly on Tegra, but you can use the flex too.
  7. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yes it is. That model in particular uses a pinout especially dedicated to V1 and v2 consoles but the outputs are there for any model. If you use a Multimeter you can find the right pinout for the Oled. Keep in mind that Oled are very special because you will need to acess very delicate points...
  8. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    This is a good solution but still demand for the motherboard to be removed for the installation mod. I’ve done more then 40 Oled’s with kamikaze mod on the upper side of the motherboard and don’t see any advantage of doing it by any other way. It take me about 4 or 5 min to reach the Dat0 point...
  9. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi. Have you tryed to use the upper side motherboard RST point? Also, you are not using ipa to clean the flux residue after your solder job. 1722808609 Why are you using SDA and SCL? Most of the Modchips with latest firmware can do instant boots if correctly installed. 1722809113 This is a...
  10. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi. Im trying to find out this litle capacitor value. Does anyone know what is his value ? Nintndeo Switch Lite alternative 3.3v. I look all around the internet but it seems impossible to find out :( 1721347200 Without it there is no backlight or image in the screen. Does anyone know where the...
  11. Viktorsilva

    Nintendo Switch Lite 3,3v missing Capacitor , happened on Picofly

    im trying to find it too. Can someone give an expert help here?
  12. Viktorsilva

    Hacking Hardware Picofly - a HWFLY switch modchip

    Forget about 2 Mosfet. You can use only one and it will work perfectly. I cannot understand why there are still people thinking on complex instalation with 2 Mosfets.
  13. Viktorsilva

    Switch oled not turning on after an attempted picofly installation

    it look like you didnt used flux. It is very important to use it otherwise you will get little balls of solder playing around the circuits.
  14. Viktorsilva

    Switch OLED die after pi fly install help please

    did you make it to work again?
  15. Viktorsilva

    Nintendo Switch Oled Blue screen due to short

    what happened to your Resistors on the cmd point ?? Switch wont boot if you dont replace them. You will need a 4,7k and 47ohm if i still remember.
  16. Viktorsilva

    Have problem with mod. Using 0.02 wire for all point

    I dont know why people still insist to use 2 mosfets connection. Done more then 100 consoles with this installation method and i can ensure you that it works with instant boots. Make sure to use at least 30 awg on CLK (CPU sends high Pulse), GRD and Power. All the rest can be connected with...
  17. Viktorsilva

    OLED getting D0 error but I have correct diode voltage

    Your Dat adapter is very Loose. Even if its working now, there is a high chance that one of this days it will stop glitching. You need to improve your anchors. You didn´t even solder the right and left ones.I hate those Dat addapters. I allways use Kamikase mod because on every 10 consoles, 2 or...
  18. Viktorsilva

    Switch OLED will not turn on. Questions about Picofly install.

    Allways put kapton tape to insolate the CPU flex solder points.
  19. Viktorsilva

    Hacking Hardware Picofly on "old" Samsung EMMC glitching fails sometimes

    That is really strange. Made more then 100 picofly installs and never care wich EMMC brand inside the Switch.Allways instant glitchs. Also installed like 30 HWfly and they were ok too, but why pay more for a Clone ?
  20. Viktorsilva

    instinct nx or hwfly picofly rp 2040

    forget about both and go for RP2040 Zero. 100ohm resistor on Dat0 and CMD, 47 Ohm on CLK and you will get a "bullet proof" hardmod. Made more than 100 installations and never had any trouble to solve.