Search results

  1. Jabba2k12ger

    Hardware Switch charges and docks fine but not detected by PC in RCM mode

    u tried installing libkusb driver with zadig..
  2. Jabba2k12ger

    Hardware Nintendo SWITCH REPLACED P13USB and mq92 chip still shorted???HELP

    unplug your emmc and look if the short is still there, sometimes a bad emmc causes this
  3. Jabba2k12ger

    Hardware Black screen on powerup

    When u try to start OFW? does it boot
  4. Jabba2k12ger

    Hardware Switch bricked?

    Hello, Have u tried to leave it for a charge a couple of hours? Sometimes the battery is so drain, the charger won`t recognize it. it`s charges very very slow in this situation. If u tried that already its hard to say, if u have a USB Amp-meter u can see how much Amp`s the Switch is going to...
  5. Jabba2k12ger

    Hacking Had switch repaired, now it won't boot to Nintendo Scree

    its sounds like a fuse mismatch or maybe a confused BQ charging IC or as Kafluke said maybe Dead Battery i will come back to you after work...
  6. Jabba2k12ger

    Hacking Had switch repaired, now it won't boot to Nintendo Scree

    you checked if your Boot0/Boot1 are ok? make a dump and compare it with your backup Nand
  7. Jabba2k12ger

    Hardware Nintendo Switch, repairing damaged or lifted pads on USB-C port !

    Respekt !!! :bow: this really helps a lot
  8. Jabba2k12ger

    Hardware Switch won't turn on

    R.I.P
  9. Jabba2k12ger

    Hardware Switch won't turn on

    looks good :) if there no shorts lets give it a try with a battery
  10. Jabba2k12ger

    Hardware Switch won't turn on

    have you tried the one without port with a charged battery if its booting :wtf: but first clean with wick the solder away
  11. Jabba2k12ger

    Hardware Switch won't turn on

    hmmm, ok ....do u have a usb amp meter, was is the switch taking?
  12. Jabba2k12ger

    Hardware Switch won't turn on

    japp ^_^ those nasty connectors....:wacko: i guess these are 2nd most hated after the sd card reader connector
  13. Jabba2k12ger

    Hardware Switch won't turn on

    oh, yes ... try it better tomorrow with the caps :D
  14. Jabba2k12ger

    Hardware switch stuck on logo when booting in emunand HELP!!!!!!!!

    have you tried to make a Hard Reset with the emunand. Volume + & - pressed at same time as Nintendo logo comes... and hold them until recovery menu is coming. and then factory reset. u can give it a try before making a new emunand. maybe it will help :blink:
  15. Jabba2k12ger

    Hardware Switch won't turn on

    Yes, that fuse .. ...and Battery Charger Chip BQ is also good around? if u have a USB Voltage measure Dongle u can check how many Amp`s the Switch is taking, or in Best Case you will see a Nintendo Logo :switch:
  16. Jabba2k12ger

    Hardware Switch won't turn on

    i would now check the caps around MT & BQ and the fuse above the USB Port. and then give it a try :)
  17. Jabba2k12ger

    Hardware Switch won't turn on

    i guess thats working fine, just that the clone will be not as precise and steady as the genuine ones. In my Setup i use a real Station with some genuine & also cheap clone Irons. The clone ones do a good job for the price.
  18. Jabba2k12ger

    Hardware switch error code 2162-0002

    Battery BQ Controller IC or MT Chip i guess
  19. Jabba2k12ger

    Hardware Switch docks only with 3rd Party Dock

    Hi, I have a strange issue with one of my Switches. It`s working fine ...the only thing is that it won`t Dock with the original Nintendo Docking, only with a 3rd party one:unsure: Had anyone similar behavior? The USB-C Port seems to be fine and its charges on both sides and with Fast...