Search results

  1. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    No problem! I've actually switched to just booting CFW on the sysNAND and I haven't been banned yet, as I don't install any NSPs. I mostly use it because of sys-tune overlay, but save editing Animal Crossing on occasion is also fun.
  2. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    It's mostly convenience, so you don't have to carry a jig and payload injector everywhere and so it's always right there. I've found mine to be quite useful, until it started acting up, and I don't quite know how to fix it besides replacing it. This also does allow booting whatever CFW you want...
  3. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I do not believe that there is any Mariko support as of yet.
  4. D

    Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

    Part one is VERY necessary. It made me think I had actually messed up my Switch when installing it with just part two. I ended up having the chip re-flashed with part one and two of Fusee Suite and it solved the problem.
  5. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Okay so I've got a bit of trouble with my Trinket. I have Fusee Suite flashed to it, but while booting it up I guess I held down the vol + or something because now a red light blinks 9 times after the green light shows after injecting a seemingly nonexistent payload or failing to find RCM...
  6. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thank you very much!
  7. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    @pyorin would this one work? https://www.amazon.com/04026D225KAT2A-MLCC-2-2uF-6-3V-pieces/dp/B00LQRT5AM/ref=mp_s_a_1_4?keywords=2.2uF+0402+size+MLCC+capacitor&qid=1583525358&sr=8-4
  8. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Whoops, I worded that poorly, sorry. I meant that I found one to buy.
  9. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    So the 3V capacitor may have flown off when I was attempting to solder it back into place. Where can I get a replacement? EDIT: Found it, sorry EDIT 2: Wait, the one I found is 6.3V exactly. Does it have to be over this or will it work?
  10. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Well just an update, the capacitors were loose so I went ahead and took them off, which may have been a stupid decision. However, I found that the two joints are bridged. I have no idea how to remove the solder, as these points are so small and close to each other. EDIT: Joints unbridged, top...
  11. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    So I just got that flux, and the two large capacitors look like they each have one end wrong. Basically, it isn't silver colored like the other end. Is this normal? I also used a multimeter and those two are the ones that don't work; the readings fluctuate on both sides. Edit: grammar, also...
  12. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thank you very much, I really appreciate all your help
  13. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Okay, thanks. Just to double check, I have all the straps in place except the USB straps and then do what you said, correct?
  14. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Ah, I think this was my problem. Question: how do I flash the chip if the USB straps are disconnected? Or do I remove the USB disconnect strap?
  15. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thanks, I might try that if I can figure out what was causing the battery drain and no charging issue
  16. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    While I wait, here's a better picture of the affected area in case anyone can figure out what happened
  17. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Okay, I don't have noclean flux, and I'm not exactly sure how to do all this, as I'm new to it. May I ask how much you would charge to fix it for me and install a trinket? EDIT: Or could you give more detailed instructions or tutorials for what you want me to do?
  18. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thanks, do I need to clean up the solder from that area or is it damaged or what? If I need to clean the solder, how do you recommend that I do that?
  19. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    So I put everything back on, made sure there was some insulation between the trinket and the metal it was resting on, and still had battery charging issues, so I took everything back off, made sure all the ribbon cables and the battery were plugged in, and it didn't boot up, and I tried to...
  20. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thanks, I just went to check on it and the battery went up by 2% so I'm hopeful and relieved. EDIT: I'm taking a break from it tonight still, but I'm very appreciative of you guys' support.