Search results

  1. HarmonyUnited

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Hello friends, I have just spent the better part of a day researching how to get my Trinket M0 hard-modded Switch to power back on after accidentally allowing it to discharge fully. I have tried leaving it charging over night in dock and just with official psu direct. I have tried all manner of...
  2. HarmonyUnited

    Homebrew Question ChoiDujourNX Firmware Update Fail.

    This thread just saved me!! APPLET MODE!!!!!!! This should be added to the release notes of ChoiDujourNX. CHEERS
  3. HarmonyUnited

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    Ok matty, I tried just the blue one... no fix. Then both, still nothing. checked continuity from usb pins to the places you showed me and they are definitely connected... I couldnt get at the little leg of that 6 legged thing where the blue and yellow were attached to. But i noticed the pad was...
  4. HarmonyUnited

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    Close up of pads area...
  5. HarmonyUnited

    Hacking Trinket M0 install troublea

    @mattytrog : I just tested a USB only device and it did not work... It powered my bluetooth audio dongle but wouldn't switch over to USB audio mode. So something is definitely up with the data lines... I checked for shorts on the +/- lines but didn't find anything. I damaged the right test pad...
  6. HarmonyUnited

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    @kylum : I checked the board for shorts on d+/- at the place where the test pins are above the usb port. Nothing bridged. During the modification process I did, however, damage the right test pad and it came up off of the board... i ended up just scratching the little trace above it and soldered...
  7. HarmonyUnited

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    Thanks for the advice. I will give it a try... the only place it could be bridging are the D+/- test points directly above the USB-C port. I will have to check that when I'm back from my trip. I will have to check the USB device deali-o... I do know that it charges through usb cable and when...
  8. HarmonyUnited

    Hacking Trinket M0 install troublea

    Hey, I don't have a pic of that strap before i removed all the wires... and i'm pretty certain the RCM strap was correct as the Trinket would dual boot for a good number of attempts... but there was a vol+ electrically stuck. I made a new post thread about all of this. But the short of it is...
  9. HarmonyUnited

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    I removed each and every trace of the install... but here are a few photos of the board before i removed all the modifications. This is right after I removed the USB disconnect strap... (as a PS, can anyone explain what this strap actually does in the trinket?) I noticed that i couldn't use my...
  10. HarmonyUnited

    Hacking Trinket M0 install troublea

    Hey @mattytrog, I've been having a similar issue with my switch too... The data lines wont accept the payload data. I took the trinket mod wires completely off the board and i still cant even use dongle payload injector either. Switch charges and also sends over HDMI when in dock... but cant...
  11. HarmonyUnited

    Hacking Troubles after SwitchBoot Trinket M0 Install... No more USB Data Flow. Assistance appreciated! :)

    Hello all, I got inspired to go through with the Trinket M0 modification for the nintendo switch. After many hours I thought I finally got it working until some strange things began to happen. First, I noticed that the volume up strap was electrically stuck as if it was pushed, but mechanically...
  12. HarmonyUnited

    Hacking Question Switch doesn't boot after downgrade from 7.0.1

    Hey @gnilwob and company, I am having the SAME EXACT issues as @KuraudoSutoraifu; exact, to the T, scenario. No Backups *sigh*... I have been trying to follow the thread of help.. I keep getting stuck when trying to make a keys.txt file and run into issues trying to get hactool to work...
General chit-chat
Help Users
    Veho @ Veho: New Myoo.