Search results

  1. O

    Hacking Speculations about Switch 2 hacking

    Yeah, after I reviewed the video I think so also.
  2. O

    Hacking Speculations about Switch 2 hacking

    https://youtube.com/@yapedode The Channel of "Günni"
  3. O

    Hacking Speculations about Switch 2 hacking

    Made a screencap while it was still in cache
  4. O

    Hacking Speculations about Switch 2 hacking

    What do we think?
  5. O

    Picofly AIO Thread

    Why not? Joy through the challenge?
  6. O

    hw_fly freshly soldered = leds blinks yellow

    Should be done since a few hours. What's the result?D o you get a green light sometimes? If not, check your SP1/SP2 soldering.
  7. O

    OLED, permanent dat0, inconsistent boots?

    Readed same thing on Twitter yesterday. Was that you? I think your adaptor is not positioned well. And even if, the friction method is not perfect and can fail every time. There are good and bad adaptors. The edge adaptor is not good with the friction method. Give it a good seat and make a...
  8. O

    Modded Switch OLED not booting HWFLY LED goes from purple to yellow/orange

    Friction is for mechanical engineers ;) Watch the new sthtetix-video@youtube, he shows very good how to reflow the chip without damaging it. A also better alternative is the two anchor adaptor not the edge one.
  9. O

    Tutorial HWFLY chips will brick your OLED. Here is how to avoid it

    Fixed a Switch with exact the same issue last friday. Don't worry, everything will be fine.
  10. O

    Tutorial HWFLY chips will brick your OLED. Here is how to avoid it

    Dat0 Adapter has bad connection. Reposition and fix with solder mask or reflow the adapter. Happens often when soldered at the anchor only.
  11. O

    Shorted USB-C with power - dead.

    Most time it's the emmc adaptor, Check the reading at the chip
  12. O

    Hacking HWFly Lite modchip does not start

    I have not tried but I think with shorted caps it won't turn on. The magic is to pull the voltage in the right moment deep enough to glitch the bct check. Not to short it continuesly.
  13. O

    Switch OLED teardown V1/V2

    Saturday Done 😎
  14. O

    Ripped off the Battery Cable

    No problem for a qualified repair shop or when you know what you are doing.
  15. O

    Tutorial How to flash the HWFLY Clone chips

    It's not installed. I wanted to do the firmware update before installation. €: Ok, keep calm. After getting a cup of coffee, the problem is gone. Now it doesn't reboot and flashes blue all the time. Maybe the usb-cable had no good fit in the connector or something else. I don't know.
  16. O

    Tutorial How to flash the HWFLY Clone chips

    Before my install today, I flashed the chip to 0.6.2. First attempts gone wrong, then it flashed well. Now the led pulses blue like usual after plugging in the usb. After a few seconds it shows a solid white/bright purple... Then it reboots and starts pulsing blue again, solid white/bright...
  17. O

    Tutorial How to flash the HWFLY Clone chips

    Flashed 0.6b2 over USB without any issues. Works as expected.
  18. O

    Switch OLED teardown V1/V2

    Typically 370 °C are good for the most things. I just wanted to say that experience and soldering time are more important than temperature. You can mess up even with the right temperature if you have no idea what you are doing. This is not a job for people who have never held a soldering iron in...
  19. O

    Switch OLED teardown V1/V2

    It's always a question of time. If you are fast at soldering, there is not problem. If you hold it there for while, it's not good. Typically it's not a problem solder this points with a chisel or a I-tip if you are experienced.
  20. O

    Switch OLED teardown V1/V2

    So small? No problems with connection?