Search results

  1. J

    Hacking Demo mode switch

    If you can get into rcm, and load payloads, I'd start with a full nand dump and try using choix to do a OFW update. Restore from backup if it fails.. Now, I'm not sure if everything is the same, so nobody knows for sure if it'll work, even after recovering from your stock,although unlikely, as...
  2. J

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Curious, if I flash part 1, to change my straps, do I also need to flash part 2 as well? I have, but curious if it's actually needed. Thanks
  3. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Finally got a decent picture of the affected area. As you can see with the arrow, the pad is gone. I added a jumper from pin 3 in the header, which from what I can tell is the Vol +, down to the "G4" Vol+ test pad. For some reason though, the volume goes down when pressing +. Edit: After...
  4. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I have a similar issue, and ripped out a pad by accident, the one after the ribbon connector, so I guess the "distination" trace. Technically I could just bring a wire from that pad / ribbon to the backside G4 correct?
  5. J

    Hardware Can I lock a game with a pin?

    I've not seen any feature like that from homebrew or nintendo itself. The only thing I could think of is a PG SD card and an adults SD card. Likely the easiest solution, but would require a reboot each time unfortunately.
  6. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    That is awesome, thank you! Curious, the line you run from the bottom of the resistor, does that go to the empty pad next to it and connects to the bottom, or directly below there? I tried using the pad next to it, in hope to fix it there, but it was like it shorted Power and Vol+ together...
  7. J

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    Would anybody have a high res scan of the PCB like in the instructions but without the markings by chance? I messed up a pad and need to repair it, but it's simply too small to see with the gear I have at home, but a scanned board would be insanely easier... I was a dummy and accidentally pulled...
  8. J

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Would anybody have a high res scan of the switch pcb with no markings? I'm trying to repair a ripped pad for the volume + button. I need to figure out where the trace leads to, and it's simply too small to do by eye with the gear I have. I know the source, pin 3 on the header, just not sure...
  9. J

    Hacking Switch cant get past sx os menu black screens.

    I had the same issue, just download a new boot.dat from the sx site and you should be good to go. Worked for me at least.
  10. J

    Hacking WIP [Trinket] [Rebug] [Others] SWITCHBOOT_UF2 / FUSEE_UF2 modchip software

    I have a quick question.. I have it installed but due to cooling mods, the trinket button is not accessible with a back press, which is fine as I was going to install a Reed switch for this purpose, but my question is, can I keep the integrated button and just use the RST pad (and ground of...
General chit-chat
Help Users
  • No one is chatting at the moment.
    The Real Jdbye @ The Real Jdbye: ballcock