Recent content by snaker

  1. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    This could be a corrupted NAND issue for various reasons. Rebuild your NAND to confirm, and then test it. If the issue persists, there may be another hardware problem with the console.
  2. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    I may not have installed 1,000 modchips, but I can confidently assure you that if the CLK signal is interrupted or the trace is cut, the screen will remain black—modchips or no modchips. I've repaired around five consoles with cut CLK tracks (tracing under the eMMC), and in every single case...
  3. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    But he assures you... :rofl2:
  4. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    Dont install in the front. If he knocked off them in the first place these is no way for him to be able to install new ones, he will make a bigger mess.
  5. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    Another switch arrived with ripped cap pads on the CPU. I want to give a big thanks to abal1000x for sharing the alternate soldering points for the MOSFET. It's amazing how it continues to impress me with its instant boot times on v2 and oled consoles!
  6. snaker

    Trying to install a DAT0 adapter in an OLED, but I get higher than suggested values readings on the point.

    Show me a high resolution pic of your adapter.
  7. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    As jkyoho said this is the best place. No need to cut anything with this placement.
  8. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    check my previous posts.
  9. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    These adapters are horrible (both of them) ! You will always have problems with such adapters. You must disgard them and use the correct ones.
  10. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    I wish you were correct but i dont think so.
  11. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    look at his pic. Its obvious either the temp is too high or he keeps the soldering iron too much time on the flex. Or the flux doesnt do its job so it makes it harder for him to solder.
  12. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    i must see the adapter point that touches the emmc ball under the microscope in order to tell you if the adpter will do. This adapter with one anchor missing is not reliable anymore, the tension might not be enough. IF you have the correct adapter, even if it has a slight angle difference there...
  13. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    Correct. If you measure with rp connected the values will be different. Reversing the probes will give you different value too so have that in mind. Also measuring according to my opinion is completely useless. If you short dat0 with dat1 no measurement will save you. For a thousand time i will...
  14. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    In the name of the holy dat0 adapters.... :rofl2: :rofl2: :rofl2:
  15. snaker

    Hacking Hardware Picofly - a HWFLY switch modchip

    Ohh that would be really nice in order to prove what i state. The best example. And for those who want the correct ones here is a link : https://www.aliexpress.com/item/1005007608016260.html?spm=a2g0o.order_list.order_list_main.11.21ef1802vzJSxm just got some and all are the correct ones...
See more