Recent content by ScrumpyJack

  1. S

    Hacking Switch error after any update, Please help

    OK Update - I had previously tried large gaps in updates so I decided to just go from 8.1.0 to 8.1.1 and it worked. So I then went up each single patch and made it up to 9.2.0. Then I went to install 10.0.0 and the same error popped up. I restored and did it again to make sure and again...
  2. S

    Hacking Switch error after any update, Please help

    Well I tried adding the line but no luck. I find it odd that even when I boot 8.1.0 stock and update through official updater, it still produces the error through the Nintendo error message. Thanks for the help so far. If you have any other ideas let me know.
  3. S

    Hacking Switch error after any update, Please help

    I haven't heard of this but I can give it a go. Do you know the line that goes in the .ini? I can search a bit for it. I posted an image of the error on screen in the 5th post in this thread. I have tried two SDs - one 64GB and one 128GB, both Samsung. sysNAND produces the same error. It...
  4. S

    Hacking Switch error after any update, Please help

    No, I don't think I've ever used a cartridge with it.
  5. S

    Hacking Switch error after any update, Please help

    I did - I said in my post I started out exfat and formatted FAT32 through Hekates partition tool. My bad, I worded it a little confusing
  6. S

    Hacking Switch error after any update, Please help

    I've formatted exfat on PC, injected Hekate, formatted through the 'Partition SD card' tool. I use 128GB card to create an emuRAW partition full (29GB) and the rest FAT32 (90ishGB). Then I create emuMMC (tried SD File and SD Partition) and boot with the following .ini config: [Atmosphere SYS]...
  7. S

    Hacking Switch error after any update, Please help

    That was one way I tried to update also... Got the same error :/
  8. S

    Hacking Switch error after any update, Please help

    I was on 8.1.0 and decided to update. I used Hekate to boot CFW and updated through AIO updater to 12.0.0. After the update I try to boot atmosphere and after the logo it shows an Atmosphere error. I tried a few different things to try to fix it but alas, it would never boot so restored using my...
  9. S

    Hardware Help diagnosing for DIY repair

    Quick update to this, sorry for bump, but I don't want to let this die in case someone else can find this useful - I swapped the BQ24193 chip out fairly easily. I purchased a solder/heat gun combo and followed TronicsFix and MyMateVince on youtube For anyone interested in DIY repair, both of...
  10. S

    Hardware Help diagnosing for DIY repair

    Still trying - USB C cable was a no-name brand. The Nintendo charger was not the culprit. Since taking it out of autoRCM mode it now registers 5v with the nintendo charger (no charge though). At this point I think I'm going to try swapping the chips - I've watched TronicsFix do a few. Are there...
  11. S

    Hardware Help diagnosing for DIY repair

    21, 22, and 23 all show 0.28v
  12. S

    Hardware Help diagnosing for DIY repair

    I havent used a third party doc, but have used a third party USB-c cable to connect to the PC.
  13. S

    Hardware Help diagnosing for DIY repair

    Pin 9: 5.00v Pin 28: 0.05v
  14. S

    Hardware Help diagnosing for DIY repair

    Good battery and PC cable pugged in: Pin 1: 0.07v Pin 2: 0.00v Pin 3: 3.60v (same as battery) Pin 4: 1.80v I upgraded from CFW 5.0.1 to CFW 8.1.0 using ChoiDujourNX
  15. S

    Hardware Help diagnosing for DIY repair

    Using the secondary battery I was able to boot the latest hekate version. I checked the battery stats and the charging status plugged into the PC = 'Not charging" and I see im slowly losing juice on this battery Trying to boot SXOS will flash the nintendo logo up for a second and then disappear...
See more