Recent content by revsgrow

  1. R

    Hardware Accidentally Removed Resistor Below The RST Solder points

    Solved! The resistor, of this sector, the oled also has the value of 4k7. Thanks!
  2. R

    Hardware Accidentally Removed Resistor Below The RST Solder points

    Hello, Is the value of the resistor at the rst point of the oled switch board also the same value? I have problems with my oled switch and I believe that this resistor is the cause of the problem. Thanks!
  3. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    so this resistor has the value of 47k ohm? I also found it strange, because the board connects normally to the original nand. It just doesn't rise or crash.
  4. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Okay, so let's go. Where to find this resistor to put it in place? Is it because of him that the glitch is not working?
  5. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Sorry, I took this image as a basis. That's why I said there wasn't. I would like to know what the value of this resistor is and where I can find it. I have a ninteno switch lite card. Can I remove this resistor from the Nintendo Switch Lite board?
  6. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    No, just the pads. There is no resistor in this location.
  7. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Wooow, actually soldering the wrong capacitor. But now I switched to the right capacitor and the same error code continued. Will it never work? I am sad. Error code ==* See images bellow. Thaaaanks!
  8. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I’m here again. I will attach photos of the new installation. I already advance that I was not successful in the glitch. Can anyone tell me where I'm going wrong? I used copper in the new installation of the mosfet. Grateful for the attention. Error code ==* (long, long, small)
  9. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Good Morning. See images bellow. Error code *== 1689346296 Hello! I forgot send a image of mosfet. See image bellow. Now the error changed. Is ==* (long, long, small). CPU always reach BCT check. (No glitch reaction.
  10. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    I realize that my installation is not the same as this one. Because this is missing a component that is connected from the source to the gate of the mosfet. I would like to know what component this is, along with the value so that I can put it in my installation. remembering that I'm not using...
  11. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    I was checking the installation scheme image and realized where I could be going wrong. I realized that from the Source to the Gate of the mosfet IR8242 there is a capacitor/resistor (I couldn't identify) that I didn't put in my installation. Could you tell me what component this is, what is...
  12. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    the error code shown when starting the switch is ==* (two long pulses and one short pulse) According to the error code, I mean this is not mosfet! but I redid the installation twice and was unsuccessful. Remembering that my APU does not have SP2 or SP2 points. So I'm looking for alternative...
  13. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Excuse me, but doing what was indicated I was not successful. Am I using a different firmware than the one indicated for this installation? I'm using firmware 2.73. Thanks!!
  14. R

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi, good evening, I'm new here in forum and i need your help. I bought a very cheap Switch V2, when i was unlocking, I realized that it already had passed in other hands. :sad: The Caps and Pads of the positive points SP1 and SP2 on the APU was removed. Is there a way of recover these Pads or...
See more