Recent content by Paulo_Suzuki

  1. Paulo_Suzuki

    Homebrew Homebrew app DBI MTP speed 15mbps-25mbps on emunand

    Hello everyone, I would like to know your reports about your experiences with the topic of this topic, has anyone managed to pass 25mbps in DBI with emunand? If yes, tell us about your configuration: Which version of DBI? What is your brand of USB cable? What is your SD card brand? I use a...
  2. Paulo_Suzuki

    Picofly in Switch V1 Erista "unknown pkg1 version hos version not supported"

    Hello, I didn't record many details because I don't use the picofly tiny anymore, it's a bad chip, I highly recommend the hwfly. But finally, regarding your question, the lite and v1 models need different resistances, if you are having problems, try placing another 47ohm resistor on dat0 and...
  3. Paulo_Suzuki

    New Nintendo 3DS (Lite) Black Screen Only Sound

    Hello everybody! I recently received a New 3DS console (small), this console suffered an impact that broke the upper screen, I already replaced it and tested it on another board, the screen is ok. However, the card that suffered the impact presents the following symptom: it turns on, displays a...
  4. Paulo_Suzuki

    ROM Hack Purple Screen of Death

    Purple screen on a modded Oled is almost certainly the CMD resistor. The value should be 4.7k. It looks like they used 30awg which is way too thick, likely broke the resistor terminal. swap those wires for 36awg. the clk via under the heatspreader is also very brittle and the most difficult...
  5. Paulo_Suzuki

    Hacking Hardware Picofly - a HWFLY switch modchip

    Purple screen on a modded Oled is almost certainly the CMD resistor. The value should be 4.7k. It looks like they used 30awg which is way too thick, likely broke the resistor terminal. swap those wires for 36awg. the clk via under the heatspreader is also very brittle and the most difficult...
  6. Paulo_Suzuki

    Hacking Question Permanent Violet Screen on Switch.

    Purple screen on a modded Oled is almost certainly the CMD resistor. The value should be 4.7k. It looks like they used 30awg which is way too thick, likely broke the resistor terminal. swap those wires for 36awg. the clk via under the heatspreader is also very brittle and the most difficult...
  7. Paulo_Suzuki

    Tutorial Fixed a Purple Screen of (Death)

    Purple screen on a modded Oled is almost certainly the CMD resistor. The value should be 4.7k. It looks like they used 30awg which is way too thick, likely broke the resistor terminal. swap those wires for 36awg. the clk via under the heatspreader is also very brittle and the most difficult...
  8. Paulo_Suzuki

    Purple/pink screen OLED after HWFLY install

    Purple screen on a modded Oled is almost certainly the CMD resistor. The value should be 4.7k. It looks like they used 30awg which is way too thick, likely broke the resistor terminal. swap those wires for 36awg. the clk via under the heatspreader is also very brittle and the most difficult...
  9. Paulo_Suzuki

    Init eMMC Failed, no NAND backups

    A tela roxa em um Oled modificado é quase certamente o resistor CMD. O valor deve ser 4,7k. Parece que eles usaram 30awg, que é muito grosso, provavelmente quebrou o terminal do resistor. troque esses fios por 36awg. o clk sob o dissipador de calor também é muito frágil e o ponto mais difícil...
  10. Paulo_Suzuki

    Tutorial Region Changing the Wii U

    Não mudei a porta, no arquivo esta porta 1337 e deixei assim, só mudei o ip, ams só obtenho erro timeout (winerror10060) I didn't change the port in wupcliente, it says port 1337 which is already in the file, is this correct or could there be other ports? I only changed the console IP, I still...
  11. Paulo_Suzuki

    Tutorial Region Changing the Wii U

    I did everything again and managed to run python to fix the sysprod, but I can't get past this step. It seems like it can't connect to the wii u, does the wii u leave it on this error screen to connect? it is already online on my wifi network.
  12. Paulo_Suzuki

    Tutorial Region Changing the Wii U

    Thanks for your answer! In the Fix section of sys_prod, I was unable to start aroma "4.Make sure the console is booting into Aroma (should be with wafel_payloader)" What should I do in this section?
  13. Paulo_Suzuki

    Tutorial Region Changing the Wii U

    Hello, I managed to proceed with everything except for the part of the mii where I always receive error 155-0206, here is my log file and print of sd files: https://drive.google.com/drive/folders/1vAd_diYS6TTeKYvo72hgTU7VehyVYfdf?usp=sharing
  14. Paulo_Suzuki

    Tutorial Region Changing the Wii U

    Anyone update for this? "Everything went fine for me, the log showed no errors at the end, but it seems like I missed something, as I can't start from aroma or the Wii U menu, I only get the black screen of the 'minutes' app, what can I do to start the aroma? thanks."
  15. Paulo_Suzuki

    Tutorial Region Changing the Wii U

    Sim, continua em minutos, devo alterar algum arquivo no cartão SD?
See more