Recent content by Myst0gan

  1. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    You can try, tbh I've never tried with less than 64 gb
  2. Myst0gan

    Switch Lite with HWFLY modchip – can’t boot Atmosphere or access OFW

    If there is no hardware issue, nor wiring problem, then I'd try to desolder all the wires from modchip and check if it boots to ofw normally
  3. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Does anyone know if picofly works also with Japanese or Chinese version of switch?? I am guessing yes, just want to be sure if anyone has already tried and succeeded in it??
  4. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yup!! If I disconnect the cmd from Picofly I get the correct error "cmd isn't connected". If I measure from the top side of cmd resistor till the end of my wire, I get 4.7 KOhm I get *== only when I disconnect clk and CPU, I've checked again both wires and diode readings, everything is normal...
  5. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    On switch OLED I'm getting everytime the same error *== "No eMMC CMD1 request (poor wiring, or dead CPU)" does anyone has any clue what it could be?? Here is what I've checked until now: 1. All the wiring, they're soldered properly (I'm using the same wire that I've already used in the past...
  6. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yesterday I've watched a vid on YT, where the dude was saying most of the time, the caps are used in electronic as filter, to reduce the noise... So my question is, could I use caps on picofly instead of the 47 ohm resistors?? I am guessing that the resistors are used also to reduce noise, since...
  7. Myst0gan

    Hacking Hardware Picofly - a HWFLY switch modchip

    Have you Have you tried with sda/scl?? The problem could be caused by long wire or also the glue from kapton tape
  8. Myst0gan

    Installing Atmosphere with a broken screen

    According to ctcaer here --> https://github.com/CTCaer/hekate/issues/898 It's possible, I just don't understand what he's saying and how to do that
  9. Myst0gan

    Installing Atmosphere with a broken screen

    I need to create emummc first, without it Autoboot won't work
  10. Myst0gan

    Installing Atmosphere with a broken screen

    How did you solved it?? I've got a modded oled with broken screen, so I can't create emummc normale a backup of the nand or the keys, since hekate doesn't support docking mode
  11. Myst0gan

    Switch OLED Screen not working after picofly

    I doubt that, if the battery were connected, the display will be the first one to say goodbye (electronic repair school on yt has an old video explaining why, he does it with a laptop screen). Which diagrams?? I still think that a trace is broken or some missing resistor 🤔
  12. Myst0gan

    Hacking Booting to hekate without eMMC?

    Impressive 👏🏽 can you make a guide?? Pdf with pictures or video. How did you figure out that emmc was completely dead?? Where have you measured 1,8V? 1705522211 How did you do that?? I'm asking just because of curiosity
  13. Myst0gan

    Hacking SWITCH NOOB PARADISE - Ask questions here

    I believe that you've already answered to yourself. OLED is better, but 99% of people buy it because of the display, it's beautiful when you play in handheld mode. Since you are also considering a V2, I'm guessing OLED display isn't your case... So, why would you complicate everything buy buying...
  14. Myst0gan

    Switch OLED Screen not working after picofly

    Have you checked front and back of the board, if anything is missing or for broken connection??
  15. Myst0gan

    Switch OLED Screen not working after picofly

    Well... If you knock off the 47k resistor near the cmd one, the screen turns purple, so I would start looking in that area (if the connector and flex cable are fine), if a connection or components are missing. Most of the components in that area should be related to the screen.
See more