Recent content by Mulanzo

  1. M

    Hacking USB Loader GX

    duplicate post
  2. M

    Hacking USB Loader GX

    I have this problem too! Been pulling my hair out over it....
  3. M

    Switch OLED teardown V1/V2

    I’m interested in trying this out. Once I connect the USB cable do I have to power the chip somehow? Or does the USB port power the chip? Also, do I need an application for the computer to recognize the chip or driver or is your app enough?
  4. M

    Switch OLED teardown V1/V2

    1208…
  5. M

    Switch OLED teardown V1/V2

    Seems like there isn’t a short and I protected the routing with solder mask so it didn’t move or get cut
  6. M

    Switch OLED teardown V1/V2

    So I’m just reinstalling a new chip and while everything was all still disassembled I powered it on and booted to hekate!!!! Then I assembled everything and screwed it all back together and now it flashes purple and then red!!!! What the heck….. could I have damaged something when reassembling?
  7. M

    Switch OLED teardown V1/V2

    My switch still boots up normally as if nothing was installed though. Wouldn’t a short on the cpu cable prevent that?
  8. M

    Switch OLED teardown V1/V2

    Can you clarify the difference between these two red lights? Mine boots straight to a solid red light. Does that mean there is a short on the ribbon connected to the CPU ( the flat thing with v1 v2 written on it)? Or is it the nand?
  9. M

    Switch OLED teardown V1/V2

    It lights up brightly verrry briefly a single time in like a bright white-blue colour then transitions to red. No blinking. Almost like a camera flash for how fast it is. Edit: just checked again and it’s 658 now and there doesn’t SEEM to be any shorts, however, some points give me a value of...
  10. M

    Switch OLED teardown V1/V2

    Getting a red light on my HWFLY Lite - mine was the one that I damaged soldering so not sure if its red because there is a short or if the chip was damaged. Anybody know how to tell? Also, does the value of the DAT0 point matter on the Multimeter? Mine is like 1.650 or something like that...
  11. M

    Switch OLED teardown V1/V2

    OOOH! I will try to salvage it. Doesn't hurt to try. Here's a closer look at the damage: Blue Square - Where the tip landed. The corner of the black chip is a little discoloured. Is this a problem? Red Square - Looks like the leg bent sideways. Is it a problem to straighten once the...
  12. M

    Switch OLED teardown V1/V2

    Pretty sure the chip is Fubar at this point. I'm not skilled enough to remove the solder bridging the three legs and I have no idea where the SMD popped off from. For the grinding spot, I used a Dremel with a tiny grinder tip on the lowest speed setting and it worked fine. The solder point...
  13. M

    Switch OLED teardown V1/V2

    Yeah it was all going pretty smoothly and the tip of the soldering iron snapped off and I ruined the chip. After this I don’t ever plan to do microsoldering again. Also, I still don’t have my Align Me chip but I did everything else. Guess I have to wait for another modchip to arrive as well...
  14. M

    Switch OLED teardown V1/V2

    I have a similar one and admittedly it works very well but because it’s operating as a monocle you don’t have any depth perception so I found it tricky to work under it.
  15. M

    Switch OLED teardown V1/V2

    Bad news - managed to solder all the wires to the motherboard and managed to solder most of the wires to the Lite Modchip but the soldering tip broke mid soldering the CPU 2 wire to the leg of the chip on the Modchip and I ended up bridging 3 legs and knocking off a resister somewhere. DAMN...
See more