Recent content by MicroRepairRX

  1. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    If damage was done with the grinding, I'd think the console wouldn't boot into OFW and work fine. Replaced emmc b/c I heard someone else had the same issue, but they probably used the dat0 adapter. Diode reaching with red prob to ground for Dat0 is 0.421 and similar for CMD and CLK readings...
  2. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Been trying to glitch the Zelda TOK OLED for days. First tried multiple hwfly version, then finally tried PicoFly and get this led pattern: =*== eMMC test failure - read failed It then boots to OFW and works fine. I've already replaced the emmc and the results are the same. Tried...
  3. M

    Help installing Hwfly v4 on Erista Patched

    Hello, is it possible to create a more detailed Thanks for the info, I've been trying to understand for a few hours what is being stated as I'm trying to use the HwFly v4 for a patched Erista as well. I tried looking up a data sheet for the GD32F350 48 pin chip but many pins are ADC. Which...
  4. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Got PicoFly on 2.67 with firmware 15.0.1. Updated to 16.0.2 using DayBreak after booting to CFW SysNand. Enabled Fat + Fat32 and kept all setting. during Daybreak update. Restarted after update completed into hekate and tried rebooting to OFW. Got a black screen, no logo. Tried booting with...
  5. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yes I think I searched for them before but I don't see any results on where to buy them. Checked both AliExpress and DigiKey.
  6. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    BREAKING DISCOVERY!! Been working on this for hours. The recommended mosfets I got worked in the dual configuration for a lite switch with samsung ram and emmc. But not for any other combination with SkHynix. The flex cable worked fine with SKHynix. I then put the problem mosfets on the...
  7. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Have you tried disconnecting all the wires? To make sure the problem is not related to the pico fly install?
  8. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    500 ohms from what two points? 2 resistors inline is 0.499 K Ohms and off circuit its 1k ohms. Took four 0.499K resistors and chained them together to ground, didn't work. Put two resistors each on the capacitor, didn't work. This was with dual mosfets. Blue to Cyan color every time...
  9. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Anyone else have success with using Mosfets on switches with SkHynix emmc? Only success I've had with mosfets is if both the emmc and ram is Samsung. If it's samsung emmc and SkyHynix ram or SkyHynix emmc and Samsung Ram then it's static blue light followed by green and OFW logo. Does not...
  10. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Is anyone going the mosfet route finding they don't work on SKHynix emmcs? Both dual and single mosfets? But the flex works fine? I just got the same behavior on V2 switch Mariko and switch lite where there is a blue light followed by green and the boot screen is OFW. The blue light does not...
  11. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    I have a question. Is SKHynix emmc supported on V2 Mariko switches? I found information that it's not but might be outdated. Someone posted that they have gotten it to work, but want to confirm. I'm using dual mosfets with the 5 wires that are short. The mosfests are the same distance away...
  12. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    I just took the mosfets off. I'm gonna try the flex and if that works try the mosfets again.
  13. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Did you use the flex cable or dual mosfets with wires?
  14. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    No, I use the dual mosfets and wires.
  15. M

    Hacking Hardware Picofly - a HWFLY switch modchip

    Okay so I tried both sets of solder points on the Mariko Switch V2 with SkHynix emmc. The light for both sets of solders points is blue then a flash of green the the OFW logo showing. Not the PicoFly logo. Resetting the chip yields the same results. There is no resistor on the RST point...
See more