Recent content by MAST3RF0X

  1. MAST3RF0X

    Hardware M92T36 or BQ24193

    Hello there! I'm back with a lot of knowledge but "0" results :-D I've "burned" 4 motherboard without results. However, my problem this time is really strange. Motherboard (I don't know if hackable, but I suppose yes) doesn't power on in any way when pressed Voltage on LCD Power 5v (should...
  2. MAST3RF0X

    Hardware No shorts - Can you help diagnose these switch symptoms?

    Hi! I suppose this is your Switch. (and from Photos I could se your Right Joycon Rail is Jumped for RCM) Remove Battery Cable Connect Cable Power Supply Check Battery Plug Pins (have you 5V for each of both Pin) If Not USB Port Broken or BQ24193 Reinsert Battery Cable (disconnect Charger)...
  3. MAST3RF0X

    Hardware M92T36 or BQ24193

    Yes I've checked. Later I will check again for safe. Also tried to rotate the USB cable without results. Maybe even if I will "swap" with another fuse it will be like a wire...It should not change anything. (but maybe is better to check carefully USB C Port)
  4. MAST3RF0X

    Hacking How to access your Switch's eMMC or microSD card as an USB disk on your PC

    Usually happen when AUTORCM is enabled. Power up you Switch in RCM Mode without inject Payload TegraRCM will find a RCM Device Keep Pressed Power for a while until unit will Power Off Wait a While (10 seconds) Power Up your switch again in RCM Mode You should be able to acces to Boot 0 Boot1...
  5. MAST3RF0X

    Hardware M92T36 or BQ24193

    Resistance Mode 200K Switch 1 : 120 only on the top Switch 2 : 130 on both side Another working Switch : 160 on both side I have here a very old Nintendo Switch Motherboard (Arrived yesterday), maybe a first version. There is no Fuse above USBC. So I was asking my self if in the Switch1 I...
  6. MAST3RF0X

    Hardware M92T36 or BQ24193

    With Diode Mode, Red on ground and black on fuse ( some Pro says this the way to check....don't know why) : 0.4 but the USB side act like is not soldered...no read. Tested the same on Switch 2 and Switch 3 (read below) and 0.4 on both sides of the fuse. Just acquired a third broken Switch 3...
  7. MAST3RF0X

    Hardware M92T36 or BQ24193

    No I've Shorted the USB Pin on Second Switch (where also I believe the M92T36 was shorted / burned because of this ...) The Fuse on first Switch act like a wall. In 5V out 0.2V The Fuse on secondo Switch act like a wire : In 5V out 5V
  8. MAST3RF0X

    Hardware M92T36 or BQ24193

    Yep...edited past post to better understand. So seems Switch 1 have the fuse gone (could be only this??). How I should change / repair it? small cap at Pin9 is working fine (same value as Switch 2, little difference 0.3 but they are quite little different seems) And Switch 2 ... I've read...
  9. MAST3RF0X

    Hardware M92T36 or BQ24193

    ...wait...I've changed Power Supply...measuring Measures Update : Check Images Switch 1 : black fuse just over the USB port is shorted? Switch 2 : just discovered it measure 5V only on one side of USBC (if cabled turned doesn't work) I've tested all Caps in Diode mode on both motherboards...
  10. MAST3RF0X

    Hardware M92T36 or BQ24193

    Here the voltage I can see.. Switch 1 is the working one but not charging Switch 2 is my switch where I shorted out something....(was working, now not anymore) Both works with Hakate Thank you a lot for your support.
  11. MAST3RF0X

    Hardware M92T36 or BQ24193

    Thank you for your fast reply. There is a way to check this chip or the only way is to replace it? Some Update Switch 1 (the one faulty where I've replace cap): Hakate Works, Battery Info says 1000Mah. Start in every way (CFWNand, CFWEemu and Sysnand). The only thing that doesn't work is...
  12. MAST3RF0X

    Hardware M92T36 or BQ24193

    Hi, just need you help :-) Should be simple.... Bought a broken Switch. Find out it was modded by someone with a triket (bed soldered). One cap near battery IC Chip BQ24193 as blowed (as far as i know it was used almost always on the dock...screen was tested ad have areas with shadows because...
  13. MAST3RF0X

    Tutorial How to play Gamecube, PS1, & N64 games from the wiiu gamepad

    I've writed down a Full Guide tutorial for WiiSxR. A lot of time wasted to find information and put togheter! Hope you will find it useful WIISXR ON WIIU : PSX PLAYSTATION EMULATION FULL TUTORIAL GUIDE
  14. MAST3RF0X

    Homebrew Official Retroarch WiiU (wip.)

    For now you should use WiiSxR. Works great with a lot of titles and support DynaRec. PSX PLAYSTATION EMULATOR WIISXR GUIDE TUTORIAL
  15. MAST3RF0X

    Homebrew Official Retroarch WiiU (wip.)

    Some times I must take a look at Clock to understand how many hours I've lost to learn.... However here the results of those days of try,try,try,try,try,try....and try. [TUTORIAL] RETROARCH SCUMMVM FOR NINTENDO WII U WITH GAMEPAD TOUCHSCREEN ENABLED (Italian and English language) Some things I...
See more
General chit-chat
Help Users
  • No one is chatting at the moment.
    K3Nv2 @ K3Nv2: https://youtu.be/9kE3Env_2AY?si=Bs6lUZ0ZIlqmYaGT