Recent content by leerz

  1. leerz

    Hacking Hardware Picofly - a HWFLY switch modchip

    best to put kapton or any form of insulating material? if your soldering is spotty, it can leave mounds and even spikes (of solder) using too much solder will also buldge that and ive seen that happen to others.
  2. leerz

    Hacking Hardware Picofly - a HWFLY switch modchip

    try to change the chip. also show the soldering work. bct copy failed means it cannot write the emmc so either a. install is bad b. emmc is about to die c. something else.
  3. leerz

    Hacking Hardware Picofly - a HWFLY switch modchip

    2.75 has been reliable, you can get 2.80 many factors can affect bootup speed 1. emmc type 2. soldering 3. ramtype & emmc combination & interference
  4. leerz

    Hacking Hardware Picofly - a HWFLY switch modchip

    what sdcard are you using,
  5. leerz

    Hardware Upgrade storage Xbox 360 fat

    on rgh no issue on retail/ non rgh, only old wd drives work no problem with the procedure (fatxplorer & hddhackr) the issue is sourcing compatible pre 2020 drives)
  6. leerz

    Homebrew Half life port compile

    yeah, but wii was still more powerful that new3ds at least cpu wise, ram much lower.
  7. leerz

    How Do I Make My Unpatched Switch Auto-Boot Into Atmosphère With an RCM Loader?

    you'd still have to if you turn it off. restarts wont need a dongle, let alone a jig (autorcm) purpose of the jig is to boot into rcm mode - it does not push payloads you still need a dongle to push payloads - and you need to be in rcm mode to push payloads unless you get yours hardmodded
  8. leerz

    Homebrew Half life port compile

    you are probably looking at xash3d wii https://github.com/F1dg3tXD/xash3d-wii aka GoldSrcGX the github project has build.sh but you might have to update around it
  9. leerz

    Homebrew unpatched v1 switch now acting like it's patched

    make sure you are using the latest hekate as the previous version had an issue with certain erista models things that can cause blackscreens when payload is pushed 1. slow payload - low quality ALI RCM payload dongles push payloads slow 2. bad sdcard or bad sdcard slot 3. bad motherboard sdcard...
  10. leerz

    Gaming [Release] DSi Language Patcher

    you probably set language patcher as default, set it to the twilightmenu's bootnds
  11. leerz

    Gaming [Release] DSi Language Patcher

    fixed it as step 0 for consistency
  12. leerz

    Gaming [Release] DSi Language Patcher

    there's a strange fix for this, 0. restore your nand backup (before language patcher, before Unlaunch 1. factory reset the dsi 2. delete all album entries / even the frames 3. delete exdata 4. update fw if you can (normally you dont have to) 5. run hax again, 6. unlaunch 7. set autoboot to...
  13. leerz

    Switch OLED teardown V1/V2

    b bent pins on fpc connector
  14. leerz

    Hacking RCM ON OLED SWITCH

    get the latest ams, hkt, sigpatch
  15. leerz

    Help about Battery Desync Fix NX

    if you drained until hekate mini battery icon, you need to turn it on again manually after a minute - if you left it there, it will charge to 11-16% and will cause inconsistent calibration. also dont press reset, you only need to save after doing 2 cycles
See more