Recent content by Kallim

  1. Kallim

    Homebrew Discussion Post homebrew ideas, suggestions, requests here

    I've no idea. But if you've got retroarch see if you can get the DS version. You could even make a forwarder.
  2. Kallim

    Homebrew RetroArch Switch

    I haven't got the games. But I'd suggested trying them on a different platform like your pc too see if there's an issue with the ROMs. You could also try lakka on the switch.
  3. Kallim

    Hacking Switch Informations by serial number - READ THE FIRST POST before asking questions

    No... Or you'll need a chip. Any serial not listed is basically newer.
  4. Kallim

    Hacking Switch Informations by serial number - READ THE FIRST POST before asking questions

    Possibly means we don't know. Early serials were unpatched, late were patched. Either look for one that's unpatched or if you've already bought it try and launch a payload. Patched switches still boot to RCM. The screen just stays black when you try and launch Hekate. Hold power for 30 seconds...
  5. Kallim

    Unable to start software after updating FW to 19.0.0 and Atmosphere to 18.0.0 (Pre-release)

    No. But there is a fix. I downloaded a hats repack for my Friends switch and old forwarders work. I'm not sure what it is maybe the new sys-patch 1.5.5... but it works. Even his old tinfoil is working I had to use the aplet version. In personally don't use the packs on my own switch. I like...
  6. Kallim

    Can someone verify that emunand still works if updating OFW to fw17?

    Sorry to bump the thread. But you should always be able to boot into hekate and cfw emunand (as long as it's not been updated). It doesn't matter what Nintendo do or what fw you are on. Basically your using either a chip or RCM hack. Nintendo can't patch that out with an update. When you...
  7. Kallim

    Ps4 on 9.00 Jailbreak Host Issue

    Ok I've just bought a PS4 off my brother. It's soft modded using a browser/usb hack. I want to remove his profile so it doesn't get banned etc. Can I delete this and add my own without updating? Also is it possible to use legit games online like the switch? I have no experience with the...
  8. Kallim

    Homebrew RELEASE L4T Lakka Switch - now with audio and Vulkan

    Shits a bit harsh.... Didn't I see you in discord before it hit the fan? 🤣
  9. Kallim

    Tutorial Pairing the joy-con on emunand and sysnand

    Hi. It's probably not quite the right thread but I'll try to help. Unfortunately it sounds like your joycon rails. First try cleaning them. Try a Friends joycon. If that also has issues you may need a new rail. They aren't hard to do if you can change thumbsticks etc. It depends how...
  10. Kallim

    Hardware My Nintendo Switch is Bricked ? ( Stuck on the Boot Screen )

    Are you confident enough to open it yourself? There's 2 modules that are on Lego clips. One is part of the game card reader and the other is just below. Check these are pressed down. If you're lucky it'll resolve the issue.
  11. Kallim

    Hardware My Nintendo Switch is Bricked ? ( Stuck on the Boot Screen )

    You can't just restore a nand backup. The backup is probably on a lower fw. The switch has a fuse count so you can't launch on a lower fw (it blows a fuse every time you update). You may be able to boot into cfwsysnand. If so run daybreak to update the fw. If you can't do that there are...
  12. Kallim

    Hacking Hardware Tutorial Tilt Switch RCM Hardmod

    You can just ground it through pin 9. This seems like a lot of work. Or you can also use pin 7 with a resistor.
  13. Kallim

    Tutorial Pairing the joy-con on emunand and sysnand

    The joycons need to be synced to sysnand first. That I'm 100% about. Syncfix copies the info from sysnand to emunand.... But I'm unsure if it'll do both. You might need to mount emmc in hekate then change it and run it again in not sure. The new BT option for atmosphere will probably only...
  14. Kallim

    Homebrew RELEASE GUI for NSP Forwarder tool for 12+

    What exactly are you trying to achieve? What do you want to run from the main switch screen? If we know what you want we can give you better help.
  15. Kallim

    faulty emmc, donor nand working, prodinfo seems fine - how to rebuild nand and userdata(profile/saves)?

    If your using the new lock pick it should still get the keys even with a damaged nand. I think it's called picklock now. You can use the prodinfo gen tool to generate new profinfo. Then nx nand manager to restore. I don't think you can use alternate keys. It might be possible but I think you...
See more