Recent content by KaiN69420

  1. K

    Switch OLED teardown V1/V2

    De9ed did my Oled for me. Very fast, great communication, and reasonable prices. If you see some of my earlier posts, you will notice I tried to do an HWFLY lite in Oled (before the new Oled specific version) and botched it pretty bad. De9ed helped me out and I have a wonderful Oled with Oled...
  2. K

    Hardware Hacking HWFLY LED Test

    It was from Ming, Hwfly Lite v3 Oled cable bundle
  3. K

    Switch OLED teardown V1/V2

    Yea I tried the solder mask and it would melt when iron got close. I removed the chip and install board back in case and nothing comes on, no screen, no fan, cpu doesn’t heat up. I tried with battery and charging cable. I plan to buy a new one and new chip and have a different installer do it.
  4. K

    Switch OLED teardown V1/V2

    If anyone needs a Switch OLED donor board DM me. I also have an HWFLY Lite as well. Probably need another cable set for it though.
  5. K

    Switch OLED teardown V1/V2

    Yea, so if that's the case what can I do? Just buy a new one?
  6. K

    Switch OLED teardown V1/V2

    So I think my issue was with the CLK point. It keeps beeping with multimeter so I think it’s grounded or a short. The problem is this copper stuff around the point where I scratched the CLK, the solder wants to stick to that and it’s grounded. Did I scratch too deep or not enough?
  7. K

    Switch OLED teardown V1/V2

    I doubt it, I can connect via USB and it seems to be doing what its supposed to be doing. I probably just messed up the soldering and fried the board. I will probably just try to sell it as a donor board
  8. K

    Switch OLED teardown V1/V2

    So with red on ground and black on the points I get: DAT0 - 494 CLK- 493 CMD- 416 RST- 458
  9. K

    Switch OLED teardown V1/V2

    Never got green, only glitching (flashing blue, then solid red or white). All the reading seem right, no shorts. Everyone says it’s DAT0, but I tested several times, even removed and replaced the adapter and I get ~800 in diode mode every time, on the adapter and on the modchip side as well...
  10. K

    Switch OLED teardown V1/V2

    I was doing red on points, black on ground, but it should read the same way I believe
  11. K

    Switch OLED teardown V1/V2

    Looks like its just dead. I tried replacing the DAT0 adapter, and doing USB debugging, but I keep getting BAD0010D. I installed the board back in the switch and I get no screen or fan when powering on.
  12. K

    Switch OLED teardown V1/V2

    Were you replying to me? If so, all the videos I see and other posts say it should reading around 2.9 in diode mode and I get nothing, nothing on chip and nothing on motherboard. Here are my readings if anyone can point me in the right direction, or if I should just trash it and start over...
  13. K

    Switch OLED teardown V1/V2

    Thank you. That’s one problem fixed. Now does anyone know why the RST point on the motherboard doesn’t give any diode reading? It’s just a solder point, so no resistor or capacitor could have burnt off, but I am not getting any reading, even after removing the chip connection
  14. K

    Hardware Hacking HWFLY LED Test

    So I received the board back and tested the connections. All connections including DAT0 (~750-850) seem to be within correct ranges. However I am getting no reading (1 on my multimeter) for the RST connection. The thing that worries me is I don’t get a reading from the motherboard even after...
  15. K

    Switch OLED teardown V1/V2

    Can anyone help me with this? I was plugging this back in and it was apparently upside down, the tweezers slipped and I pulled the black cable from the connector. Is there an easy way to repair, or do I need to purchase a new 2-pin JST connector (if anyone knows the size that would help) and...
See more