Recent content by jacobtc

  1. jacobtc

    Tutorial PS5 Exploit Guide

    Was that a response to me? Also, I might need to read up on all this stuff.
  2. jacobtc

    Tutorial PS5 Exploit Guide

    I don't, I never really used the console after buying it used :rofl:
  3. jacobtc

    Tutorial PS5 Exploit Guide

    I'm new in PS5 JB land, and have a PS5 Slim with disc on 10.60. Should I just wait or are there anything I can do now?
  4. jacobtc

    EDM-010 - 80800014 - TPM 2.0 chip / power failure

    Both are 4.5 kohm Also did a reflow of the TPM, but no change. Also, I do get 3V3 on Pin 8 and 22 when applying power, but goes away after a couple seconds.
  5. jacobtc

    EDM-010 - 80800014 - TPM 2.0 chip / power failure

    My measurements are completely different on most pins:
  6. jacobtc

    EDM-010 - 80800014 - TPM 2.0 chip / power failure

    Yeah, I just measured and get 3.3V when DC is connected, but it stops after a couple seconds. Not sure what to troubleshoot next. I don't get the 1.8V rails as mentioned in the OP, but should those only be present at start button press?
  7. jacobtc

    EDM-010 - 80800014 - TPM 2.0 chip / power failure

    I have this EDM-010 which I know is a very low firmware, however I can't figure out the fault. It turns on blue, one sec and then off. UART gives me 80800014 - TPM 2.0 chip / power failure. I've checked VCC on the TPM and I get 0v, so not power is going there. I checked 1.8V out of the DA9065...
  8. jacobtc

    PS5 EDM 020 TPM Issue

    Hey, did you solve the issue? I too have the same errors on a PS5 with 1sec blod.
  9. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    Oh! That makes sense, thought he did all three in series on all lines :D
  10. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    Do you have a picture? How do you fit that many resistors? :D I have two Erista's with some weird error, one has a EMMC slow error, and the other, Atmosphere just errors out, or doesn't boot. Booting to OFW seems to work fine on both. EDIT: Also, wouldn't a 240ohm resistor do the same as...
  11. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks! Not sure if I should just do a re-ball.
  12. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks! The thread has become quite long, so it is difficult to find whether someone has done modifications etc.
  13. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    What adaptor would you recommend?
  14. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    I'm struggling getting the DAT0 adaptor to seat where it should. It seems to only get a 0.7V diode reading when shifted slightly right, but that seems to be a ball width, so the reading I'm getting is probably from a neighbouring ball under the EMMC. Is this normal? I tried with two adaptors...
  15. jacobtc

    Hacking Hardware Picofly - a HWFLY switch modchip

    Alright, looks good. Yeah taking Ground from the shielding would probably have been easier, but oh well 😅 Also I will probably redo it with a combined Gate wire.
See more