Recent content by iO-bUGGY

  1. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Can I flash directly to 2.64 brand new rpzero or do I have to flash 2.5 + update than 2.64?
  2. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thats what I confirmed with this glich and the toshiba mosfets.
  3. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Guys I had a mariko v2 and tested hac-cpu-21, Tested the 2 mosfets from a donor board and it works like a charm. Instant glich. this are I think toshiba ssm6k504nu. I've tested the mosfets from hwfly v2 flex are not working. I've tested the mosfets from hwfly v2 felx on 3 switches.Non worked...
  4. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Guys Does the length of the wires matter?I saw so many comments that need more length for it to work?
  5. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    No problem man,I found that the resistor is a 3.7k ohm.
  6. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    The one on the board side.ot the one on the rp2040 47OHM. I knocked of the resistor on the board cmd resistor.
  7. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Can someone tell me the value of the cmd resistor on the OLED?
  8. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Guys did anyone use 0.10 wire for mod and does it work as I think it's to thin? Can someone confirm that works.
  9. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    Your iron is not to hot,that is why it did that.Try remping up the heat and use flux a good one and check with multimetter for shorted cap.if there is none then you can power on the switch to see if it works.
  10. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've installed the mosfet directly to the cpu as I had the flex broken when testing source, No continuety. But after hours of testing I don't know why I lost 3.3v on +7780 ic is missing 1.8v enable to start produce the 3.3v and when testing the caps near the +7780 it only rised up to 0.056mv. So...
  11. iO-bUGGY

    Nintendo Switch OLED - help with component

    The value of the comonent is 105ohm resistor
  12. iO-bUGGY

    Hardware Nintendo switch missing 3.3v rail.

    Hi Guys, I'm missing 3.3v rail on the +7760 near the 2 big caps. 3.3v I'm getting like 0.056mv and it does not rise. Does anyone know where the 3.3v is created. I've even replaced the M92t36 to see if that is the one but nothing the problem persists.
  13. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've disconnected the flex and checked the flex.The continuety is there up to the mosfet.No problem there. 1680778895 I'm using a felx cable form the hwfly v2 flex and has 2 mosfets
  14. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've retouched the caps for better connection and the connection are solid. I don't know what to do else. Can it be the mosfets are bad?
  15. iO-bUGGY

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've brifdged the 3-4pin done that but no metter what I get blue than cyan color
See more