Recent content by Harak

  1. Harak

    Hardware Nintendo switch backlight bug no display after rp2040 installation

    I think you destroey your lcd connector. this happens very easy especially if you re a beginner. please upload images from your lcd connector to see all the pins. thanks
  2. Harak

    Hacking Hardware Need help with New 240plus chip on Switch V1 (XAJ4) patched — no display after install

    Please upload some images of your work to evaluate problems better. thanks
  3. Harak

    Weird Problem after Modfail Switch Lite

    Hello, i got a Switch lite from a client with a failed Modchip. He removed everything and now i have it on my bench. checked the usbc meter and it was charging the battery normally, but no screen, no boot under the microscope i checked all mod points and noticed that the sp1 and sp2 caps are...
  4. Harak

    Switch Lite turn off after Nintendo Logo after resetting the console

    Alright. I think I should install a picofly and see whats going on with the nand
  5. Harak

    Switch Lite turn off after Nintendo Logo after resetting the console

    Yes it does turn off even if it is plugged in. Did the volume start multiple times. No success. If I need to rebuild Nand I think this is only possible with backed up nand? Which I dont have.
  6. Harak

    Switch Lite turn off after Nintendo Logo after resetting the console

    Hello, as I wrote. I resetted the console to sell it. Afterwards I cannot start it. It is charging though. I can see it from the Battery Smybol. But when I try to the Nintendo Logo (not the Switch Logo) appears for some seconds and then it turns off. I dont know what to do. I hope you guys can...
  7. Harak

    Switch Oled won't detect right joy-con after installing picofly

    Forgot to answer it but I solved my problem. For me it was the connector who did not worked. With a slightly press the joycon was detected. After switching the connector everythinl worked perfectly fine. So be carfeul and check also the connector.
  8. Harak

    Have Xbox One and Series X Controller and the Dualsense the same Stick for replacement?

    For me it worked.
  9. Harak

    Switch V1 RCM not working after Battery replacement

    As I said I checked the Usb C Port regarding continuity and diode Values. Continuity is good but diode values are bad. Long story short replaced the filter which are connected to D+ and D- Pins and Rcm Loader is working perfectly fine. The question is now, did the Client know the problem and...
  10. Harak

    Switch V1 RCM not working after Battery replacement

    I have no clue what a rcmx86 is but i googled it. I dont have that board. Just the rcmloader. I have a breakout board. But I think it is worthless without the rcmx86. Usb c port looks good. I will check it with the microscope in the evening
  11. Harak

    Switch V1 RCM not working after Battery replacement

    A little late Update. Usb C is charging as mentioned but some Pins are showing different values in diode mode compared with a known good one. Checked also contuinity and those looked good so sonething on the baord must be failing. After opening I found a bad filter. I will replace it and will...
  12. Harak

    Switch V1 RCM not working after Battery replacement

    It is charging normally. I will check all pins from the usb c port today and will try that tip with the emmc out. Will keep you updated. Thanks in advance.
  13. Harak

    Switch V1 RCM not working after Battery replacement

    Yes!
  14. Harak

    Switch V1 RCM not working after Battery replacement

    I have also a jig. But it does not work. Yeah next time i will definetly try everything before. But as i said. Ofw is working fine. But why is the jig not working.
  15. Harak

    Hardware Project XZZ's Switch Boardviews Cracked!

    I thought there is no diode value with flexbv So i was hoping for openboardbiew will be delivered woth this feature to in the future
See more