Recent content by FXDX

  1. FXDX

    PS5 displays logo then shot down!

    Update Uart error log: $ [MANU] [ACINDET] AC IN DETECT Low:A7 OK 00000000:3A $$ [MANU] UART CMD READY:36 errlog 0B OK 00000000 80802220 02A4B0BE FFFF0005 00000100 2013 0036 234D 1708:3A Error code: 80802220 Description: Known Unknown 80802220 (Power or Short) - Report Findings I changed the...
  2. FXDX

    PS5 displays logo then shot down!

    The liquid metal is cleaned and put back another new one with great care. It doesn't give me any error, simply after the PS logo appears, it shut down. I repeat in safe mode, there is no problem, I can stay there for an hour. I thought about some RAM memory ?!?
  3. FXDX

    PS5 displays logo then shot down!

    Hello. I have a PS5 that has the following problem. It starts but when it reaches the logo and should enter the dashboard, it suddenly stops. If I enter safe mode, I have no problem, I can navigate through the settings without stopping. I tried reinstalling fw and recovery, nothing worked. How...
  4. FXDX

    Hacking Hardware How to solder Kamikaze Dat0 point?

    after you have drilled and you gave it DAT0 point, clean it well with isopropyl alcohol, apply flux and with the thin tip from the soldering station dot a little tin. Flux is the key and the thin tip of the soldering station !! Don't forget after to apply the UV mask.
  5. FXDX

    Swap OLED Tegra SoC & eMMC from a donor board !

    I bought the board from ebay, someone who tried to expose his DAT0 alone at home without the necessary knowledge, without experience through the kamikaze method and failed by sectioning several layers. The price was ok and I was lucky that Tegra and eMMC were ok!
  6. FXDX

    Swap OLED Tegra SoC & eMMC from a donor board !

    You are right....It's an Frankenstein OLED:rofl2::rofl2:
  7. FXDX

    Swap OLED Tegra SoC & eMMC from a donor board !

    Story In short. I received a modded OLED with a Hwfly modchip in the service, in which, for unknown reasons, the Tegra SoC processor shorted out, with no chance of repair. The only chance was to swap the Tegra processor and eMMC memory from a defective OLED donor board. I removed the two paired...
  8. FXDX

    Oled Picofly with copper pad DATO point, using the Kamikaze method!

    I think so 1709672344 I do not recommend because it does not dig evenly. More tears....
  9. FXDX

    Oled Picofly with copper pad DATO point, using the Kamikaze method!

    MaAnt D1 with C.1.004 Extra hard milling cutters for lab use
  10. FXDX

    Oled Picofly with copper pad DATO point, using the Kamikaze method!

    Before, I always put the mosfet on the back and it worked perfectly every time, but recently I started putting the mosfet Flex Cable For Core Or SX Core Chip, on the Tegra. This way, I don't have to remove the board from the console anymore.
  11. FXDX

    Oled Picofly with copper pad DATO point, using the Kamikaze method!

    The ''kamikaze'' OLED method by which you expose the DATO alternative point, drilling up to the third layer in the board exactly as you can see in the picture, although it is very risky for an unskilled person, requiring special skills and tools, it is much easier to solder wire to that...
  12. FXDX

    Hacking Hardware Picofly - a HWFLY switch modchip

    The Wi-Fi chipset had to be reflowed or replaced. Does not require Tegra reball...
  13. FXDX

    Hacking Hardware Picofly - a HWFLY switch modchip

    It's good. Be careful how you insulate well with the UV mask.