Recent content by frozenboy

  1. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    I ve tried 101, and 104 but not work, it seem ceramic cap is not ok
  2. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks, more choice, but I prefer soldering in to the cap, it easy to melt than this big via, because the heat is hard to concentrate to the large surface of the via and a cold point is easy to happen.
  3. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    thanks, I will get the 0.1uF tmr, btw, is there any kind 0.1uF bigger, your pic seem so small and hard to soldering
  4. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    this one, these cap is so tiny
  5. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    I am using the cap at the third pin below the rp2040, the led seem not work right, It show green but not blinking, not stable at all. The led on rp2040 also get interference from this second led, it became red. I guess a bigger cap or sth wrong with wiring. About wire and wireless mode still...
  6. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    I have checked your oled pinout, it seem the orange pin is just suitable for D and yellow next to it for gnd. both pin is huge and got big cap that easy to soldering. Have you tried it, maybe next time I would give it a shot
  7. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    I've check the cap on oled, it quite good point, avoid open apu shield, clean paste... and just get D point from it could save lot of time. But for the s pin, I won't risk it. S point can get from any gnd pad
  8. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    good to know this, could be useful someday, but for now I afraid of bridging pin more than open apu shield, in the pic of oled, the cap is quite close to other component. Pretty sure this kind of installation never appear elsewhere. So if you want to make a video about that. It is ok, but be...
  9. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Yes it does,47 ohm, i just install it yesterday. Can you repost the schema for your version that dont need open cpu cover. Previous pic is quite hard to follow About the led, i think that using pin in the rail is easier than the main board. Another idea like add another pin for the joycon led is...
  10. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Sorry for that. I missed the previous post, and cant find delete button
  11. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Do you have any alternative fix for this. maybe using another pin for the signal.
  12. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Looking forward to your schematic, the joycon also need some wired right?
  13. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi everyone again. I got rp2040 tiny with grb mode, how could i change it to rgb mode, I dont want to make another fw just for led color
  14. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    If you got black screen, then check slow mmc mode benchmark to see if it is the case,if it does, add more resistor
  15. F

    Hacking Hardware Picofly - a HWFLY switch modchip

    Thanks, I am used 6.1 which is missing this one, I also check in a github page, but it seem it is just cloned version of rehius which also outdated
See more