Recent content by flduch

  1. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    My switch is living again as before ! Thanks to all that help me to recover my briked switch. Without your help it couldn't repair my switch. Thanks again and wish all the best :-)
  2. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    Thanks a lot ZachyCatGames, now I can reuse LockPick_RCM and BisKeyDump attesting that the encrypted keyblobs in Boot0 are now valid ! Now I have to follow the way to recover my switch as before.
  3. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    Ok mattyrog, hope that SciresM can give me good advices. May I use now the switch as "standard" switch and connect it on the internet for doing some firmware updates ? May I risk to be banned ? Thanks
  4. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    When you write "Regenerating them? Yep, I think it can be done.", I believe you don't say how ? To be certain : no way to encrypt the keyblobs into Boot0 = nothing to do excepted use originals gaming cartridges ?
  5. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    I've check the content of Boot0. The keyblobs should start at offset 0x180000 increment of 0x200 for each one (keyblob 0 is at offset 0x180000, keyblob1 is at 0x180200, etc). In the Boot0 at 0x180000 : I see " [config]..autoboot=0..autoboot_list ..." The other keyblob are all 00" The keyblobs...
  6. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    If the keyblobs are intact, why for exemple Lockpick_RCM saying me that they are corrupted now ? Is that normal ? I use many times a procedure using choidujour to bring my switch back. It nevers work (even choidujour create smaller Boot0/1) I've used the files generated by choidujour and my own...
  7. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    I've may be understand, there are two tutos right ? The first one I've used is on \Unbrick_Your_Switch_iha2 and the second one is on \Unbrick_Your_Switch_iha2\Unbrick_Your_Switch_iha2. Now I've tried the second one and goes until the step "launch hekate_switchboot_mod and ... the switch started...
  8. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    Ok mattyrog, First, I don't believe we are working on the same tuto : I use this from your message on friday (last week) at 1:46 PM Where can I found the right one ? Second, can you tell me what write the keyblobs of my switch into Boot 0 ? (Switchboot, hekate_switchboot_mod?) Thx
  9. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    I just follow your tuto and write le directory "Dump to SD" to the SD card. What write the keyblobs of my switch into Boot 0 ? (Switchboot ?)
  10. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    No I haven't any theme installed
  11. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    I'm sorry but it isn't clear for me what I've to do ? Can you please tell me what you mean by "Remove theme in 5.1.0, then update" Thx for helping me
  12. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    Hello mattytrog, I follow your tuto \Brief_Instructions.txt (not \Unbrick_Your_Switch_iha2\Brief_Instructions.txt) with success until the step "Launch fusee-primary.bin". After starting Launch fusee-primary.bin, I've gotten the message : ERROR : Fatal Error: (NXBOOT) Key derivation failed ! I...
  13. F

    Homebrew Question Would it be "legal" for me to post "blank" boot0 / 1 for repair purposes?

    Hello mattytrog, I've tried Unbrick_Your_Switch and the firt time I've done it, by launching fusee-primary.bin, I got the message : ERROR : Fatal Error: (NXBOOT) Key derivation failed ! Now I can't start switchboot.bin ( Atlas NX logo is displayed, Nintendo logo is displayed and ... black...
  14. F

    Hacking How do I recover from lost Boot0

    @thesjaakspoiler : thx for your advise but both threads do not help me. The problem is that I have to know how to inject the keyblobs on an encrypted form derived from the console's SBK (Secure Boot Key) into the Boot0. Without doing this, the switch can't boot.
  15. F

    Hacking GUIDE - How to recover installed games and their save data from a bricked emunand

    Did your switch have a 100 % Boot0 unvalid or lost ?
See more