Recent content by DuffGnR

  1. DuffGnR

    Hardware Nintendo Switch OLED - “Unable To Access SD Card”

    Did you manage to solve it? If yes, how? I have the same problem and I believe it is not on the daughter board, as I tested another one and nothing changed. I used 3 different cards (Lexar, Samsung and Sandisk) and only one Sandisk works without initialization errors. On Hekate, the other two...
  2. DuffGnR

    Failed to Init SD Card w multiple 256gb cards, Works with 64gb

    Did anyone manage to solve it? I have the same problem on a Switch Oled. It works perfectly with a 128GB Sandisk Extreme card, however, when I apply a 256GB Lexar or Samsung Evo Plus (Both 100% genuine) it gives the same error when starting up. The Samsung still boots sometimes, but it has flaws...
  3. DuffGnR

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    So, my case was a bad installation in the postfix of Dat0, although it was signaling well in the multimeter measurement. Anyway, if I were you, I would try to reinstall such postfix, as it can cause damage to your nand in the future. Ideal is always to boot without problems, both Nand...
  4. DuffGnR

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    It did. I reinstalled the chip and changed the postfix, it was great. also check the other installations as well as cleaning after installation. Another item to be observed is the resistor, I changed them all to 47ohms.
  5. DuffGnR

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    Thanks, I'll do that.
  6. DuffGnR

    Picofly AIO Thread

    Thanks. Im going to try.
  7. DuffGnR

    No more old HWFLY CHIP new rev on RP2040

    Yes.
  8. DuffGnR

    Picofly AIO Thread

    That's not the point. I bought the chip that comes ready to go, just install. The chip is very similar to the HWFly, the same pattern, but with the RP2040 system. The issue of resistors had not been passed by the dealer or creators until this point, not in this new chip standard. Anyway thank...
  9. DuffGnR

    Hacking Hardware HWfly-shaped Picofly boards start shipping in China

    I have a problem, I installed the RP2040 which is very similar to the HWFly model, but it always boots in emunand and sometimes I can boot in OFW, but sometimes it hangs on the Nintendo Switch logo when I try to boot in OFW, or it gives an error 2002-3539 /3540, does anyone know how to solve...
  10. DuffGnR

    No more old HWFLY CHIP new rev on RP2040

    I have a problem, I installed the RP2040 which is very similar to the HWFly model, but it always boots in emunand and sometimes I can boot in OFW, but sometimes it hangs on the Nintendo Switch logo when I try to boot in OFW, or it gives an error 2002-3539 /3540, does anyone know how to solve...
  11. DuffGnR

    Hacking Hardware emmc slower mode (200 MB/s) - hwfly V5

    Did you manage to solve the problem? I have a very similar problem but I installed the RP2040 model which is very similar to the HWFly format, and sometimes OFW doesn't work, only Emunand.
  12. DuffGnR

    Picofly AIO Thread

    I have exactly the same problem, I installed the RP2040 which is very similar to the HWFly model, however it boots in emunand and sometimes I can boot in OFW, but sometimes it hangs on the Nintendo Switch logo, other times it gives an error 2002-3539/3540, does anyone know how to solve this...
  13. DuffGnR

    Picofly (RP2040) OLED getting error Failed to init eMMC. But with HWFLY working fine.

    I have exactly the same problem, I installed the RP2040 which is very similar to the HWFly model, however it boots in emunand and sometimes I can boot in OFW, but sometimes it hangs on the Nintendo Switch logo, other times it gives an error 2002-3539/3540, does anyone know how to solve this problem?
See more