Recent content by detilmalala

  1. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, I am having problems creating emummc in erista with firm 22.1..0, does anyone know how to solve it?
  2. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello friends, at the point indicated with the arrow I have a short to ground, I have already injected voltage and nothing heats up. Does anyone know which component may be shorted, I already lifted that piece and at that point on the board I have the short to ground
  3. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    have two resistor the same value??
  4. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hello, please help with the value of those 2 resistors on the v2 board. Those inside the yellow circle
  5. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    compared to a functional oled board, it gives me half the value, that's why I ask, I will have to change that ic max 77812 and try
  6. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    no no, in figure 2, I removed the coil and the side that is marked in red measures 50 in diode drop. what should i do? I already injected 1 volt at that point and there is no consumption
  7. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Can you point it out in the image for me? 1751137888 Update: I have made measurements and I have a low diode drop in the points marked in red, I removed the coil and on the marked side it measures 50 in diode drop, I don't know which part of the board that end is connected to, I would...
  8. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Can you point out what that reducing chip would be?
  9. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    I measured the point marked in red on a working board, and the value is between 300 and 350. That's why I ask...
  10. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    HELP please!!! I have an OLED switch that does not turn on, at the point marked in red I have a measurement of 200 with the multimeter in diode drop. I removed the IC and the same measurement continues, does anyone know where that line goes on the board? I add: the fault occurred because I left...
  11. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    i think you did not understand, only firs time was cut, pico show with light, then i fixed the clk track, but console does not work, only hekate
  12. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    If you think I'm wrong you can try it on an OLED and you will see that it is like that, and then the console will not work, as I said it has happened to me more than once and I have installed more than 1000 chips
  13. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    I can assure you that if you cut the clk track and connect the chip on the opposite side of the cpu, the white light appears and the console is useless, only the hekate works, I'm going to try with a donated nand to see if I fix it
  14. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    It is not like that, in more than one console it has happened to me that I have placed the chip with the clk cut off and the white light does appear, my assumption is that it corrupts the nand, I am going to see if I fix it using the sthetix level unbrick method 2
  15. D

    Hacking Hardware Picofly - a HWFLY switch modchip

    Ok, and what consequences would loading the payload have on the emmc, if it were done with the clk point cut, in the place that is marked in green, but not making contact with the cpu, because after that the console stopped working
See more