Recent content by Daddy_Daycare

  1. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Hey man. Sorry I didn't respond. I haven't been on the site since my last post. Pretty much gave up. It will charge but only in one direction. If that makes sense. Pins in the USB c port got damaged so now it only charges if you plug it one way not either way. So the port isn't bidirectional...
  2. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thanks for your help. I think I'm just going to call it. I don't know if something got messed up when my son yanked the charging cord out but I have tried both sets of data points on the switch mobo. Front and back. I've also soldered and resoldered the points on the gemma and nothing changes.
  3. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    About as good a pic as I can get. It was really pretty when I first soldered it up but I've messed with it so much the pads are starting to come up. I'm about done with it honestly. I have no clue. I have tried the USB pads on both sides of the switch mobo with no luck. Currently have the...
  4. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I haven't made it home yet but in thinking about things I wanted to make sure I programmed the gemma correctly. I connected to the PC. Pressed reset 2 times and then copied part 1 of fusee. After it copied and the gemma rebooted I pressed reset 2 times and then copied part 2.
  5. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Ok I will as soon as I get home
  6. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Gemma Install Stuck and could use some help I am doing a gemma install. When I turn it on it goes into rcm but the screen just stays black. The gemma flashes yellow a few times then red then there is a slight pause followed by 1 last red flash. There is nothing on the screen. Sx loader is on my...
  7. D

    Hardware Right Joycon Not Showing As Connected When In Rail

    Does anyone know which pin on the right joycon is responsible for signaling when the joycon is docked in the joycon rail? Mine will connect via bluetooth but when you put it in the joycon rail it doesn't show as docked. I think I may have accidently shorted something when I did my trinket install.
  8. D

    Hardware Where does the pin 10-joycon strap go on the back?

    Ok thank you I will give that a shot.
  9. D

    Hardware Where does the pin 10-joycon strap go on the back?

    The k you for the reply. That is the guide I used. Long story short the dog got tangled in the solder station cord and the trace for the joycon strap got destroyed. So I'm trying to figure out where the travel goes after it ends at the point I circles in the attached pic.
  10. D

    Hardware Where does the pin 10-joycon strap go on the back?

    So I'm an idiot and during a trinket install the pads for the joycon on strap got pulled up. Does anyone know where that trace goes on the back so that I can jump it and fix the connection. I know it goes to pin 10 on the joy on but no idea where it goes on the back of the motherboard. The...
  11. D

    Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

    That makes sense. I'll give that a look. Thank you for your help
  12. D

    Tutorial Trinket Internal Install.

    Both of my pads came off. Long story. Is there anywhere to connect a jumper to fix this? My right joy on isn't recognized when it's docked and I cant enter rcm mode now.
  13. D

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Need a little help if possible. Long story short the solder pads for the joy on strap got pulled up on my switch. So now the right joy on is not connecting when in the joy on rail. It still work but only via blue tooth. This also means I can't enter rcm. Does anyone know another point on the...
  14. D

    Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

    I can not get this figured out. I flashed the trinket as instructed and installed. The payload is on the sd card and when I started it up in rcm it flashes yellow a few times and the after a short pause it blinks red once. It never seems to push the payload and I'm left on a black screen
  15. D

    Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

    Awesome thanks auto Awesome thank you.
See more