Recent content by cicci084

  1. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Hi bro.Thx you. work!!! Woooooork!!! i'm Happy.. Out of over 100 consoles, it's the first one that burned out my MOSFETs. Installing underneath, it worked. THX!
  2. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    i try.,..
  3. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Sorry guys. I know I'm clogging up the discussion. I installed three MOSFETs, and they all burned out. What am I doing wrong? What could be causing the above? I should point out that I have four layers of Kapton, so there's no way they're touching the shield.
  4. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Never tried 1. Always done everything with wires, always. This is the first console (I've made about 100) that's given me this problem.
  5. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Good evening, everyone. I have no explanation. I can't work with this OLED. Even with the 47 ohm resistors on dat0 and cmd, nothing. No glitches, just = = * After several attempts, I disassembled a console with a chip installed (this one is also OLED, which glitches perfectly) and took both...
  6. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Changed picofly, same result. Resistori 47Ohm no try. Never problem with 100ohm resistor. I try?
  7. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Good evening, everyone. I'll start by saying I have little experience with errors. Personally, I've done a lot of installations (I think about 100). Today I installed a PicoFly OLED and I get = = *. The codes tell me to check the MOSFET. I replaced the MOSFET, the chip, and the resistors. Always...
  8. C

    help with pfbneo on FW 21.x

    So, let's start with the fact that I use Hats by sthetix. So, if I go to Album, I get directly to HBmenu. If I press and hold "R" and start Pfbneo, I always get a crash. Now, should I always try the forwarder method? 1767733410 work! forwarder mode, it's work! Thx!
  9. C

    help with pfbneo on FW 21.x

    Thanks, but I simply overwrote the nro file and am getting atmosphere crashes. Now I'd like to try your instructions, but I'm not entirely clear because I've never done it. If you could walk me through it step by step, I'd be grateful.
  10. C

    help with pfbneo on FW 21.x

    If you have any ideas that could help me, I would be grateful.
  11. C

    help with pfbneo on FW 21.x

    i try now. thx bro 1767556960 Excuse my ignorance. I take the nro file, put it in the switch folder, go to album, click on the pfbneo icon, and everything crashes. On older firmware, I remember installing an nsp or xci file, then copying the contents of the file archive (roms, bios, etc.) to the...
  12. C

    help with pfbneo on FW 21.x

    Good evening everyone. I'm asking for help from you experts as I can't launch pfbneo on firmware 21. In previous versions (fw 17, 18, 19) everything worked fine. Could you help me?
  13. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    The codes said eMMC reading error. It had never happened to me before; in each case, I replaced the chip and it worked. I'll test that chip on the next console. Thanks.
  14. C

    Hacking Hardware Picofly - a HWFLY switch modchip

    Evening, I'm switching to firmware 21. I get a short yellow flash, a long one, another short one, and then it boots in OFW. As it boots, it repeats the same flash sequence. With this sequence, the guide error reports: No eMMC block 0 read (eMMC init failure?) Of course, I've checked everything...
  15. C

    Homebrew [Release] GodMode9 Scripts Megathread

    Hi guys, trying to follow this guide, I get this error.
See more