Recent content by azxc

  1. A

    I want to hack my switch to resolve unforeseen consequences

    Just create a new acc and you can delete the first one. It just needs to have one linked all the time
  2. A

    Anyone here successfully(or not) hardmod an OLED switch?

    If you have a decent microscope, hot air station, soldering iron, with enough patience it shouldn't be a problem. The most dangerous part would probably be reflowing the emmc.
  3. A

    Hacking RELEASE [Trinket] [Rebug] [Others] [Modchip Software] *NEW* Fusee_Suite UF2 packages

    He wrote this on his github page here: https://github.com/mattytrog/FUSEE_SUITE "I have been away for over 2 years so this is going to take me a while to get back correct. I can no longer access my old account on GBATemp." Perhaps a mod or someone can help him gain access to his account again
  4. A

    Hacking COMPLETED BASIC MODCHIP / DONGLE UF2 SD BOOT FILES. Trinket / Rebug / RCMX86 / Others

    Hello again, thank you so much for your continuous development and support on this. I have an itsybitsy m0 express installed. Very simple install, two data wires and the 3.3v, and gnd on chip that i soldered myself. (not sure which install method to call it) Have autoRCM enabled so chip detects...
  5. A

    Hardware Back Metal plate removal?

    I've been playing my switch without a backplate docked, sometimes for hours for a few months now. Haven't had any issue. The fan does kick in a little faster. I bet there are temp sensors in the gpu to turn off if it gets too hot like most, if not all electronic devices. Just make sure you put...
  6. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Everyone's talking about the shielding, i just removed mine. It gives a nice appearance with my clear housing and leaves room for the m0! It IS thermally connected to the soc but i don't think it makes much of a difference and there are temperature sensors in the switch to shut down if it gets...
  7. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    what kind of epoxy? Not JB weld? Yes on the drives MS tried to stop ppl soldering to the chip by drowning it in epoxy, but a little heat and some tweezers pulled it right off. Then you had people taking a grider to the chip while it was powered on..."kamikaze" "hack" \but was really just borking...
  8. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I'm a neat freak with wires and tend to make them look pretty, it is a habit that has screwed me over more than once, but its especially important with my clear switch shell. Also if there's a wire that stray away on top of a screw hole when your putting things together it will crush/break the...
  9. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Edit
  10. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Thanks for all of your help! Flashed SXOS UF2 files and it works well! :) Couldn't seem to get the ShaXLoader to work on my itsy but ill tinker more with it later. Today was well spent ! EDIT: what brand of epoxy do you use? I tend to use hot glue. super glue is conductive!!! I've borked more...
  11. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Itsy, i meant. It won't show up now after it's installed in the switch as a usb device. i have the switch powered off.
  12. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    I plugged trinket in before installing it, and deleted everything on it. then dragged and droped the three files from the zip into the itsyboot storage device.
  13. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Ended up soldering the 3v line directly to the M92T36 and it appears to be working! :) when i'm in RCM the trinket just slowly flashes a green LED, and pressing reset on it does nothing but light up both LEDs and then go back to the flashing green LED. when i boot normally, it boots normally...
  14. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    Here's my install so far! Just need a way to get 3V :) you can see where i borked a cap and the original 3v line guys...
  15. A

    Tutorial Internal modchip - SAMD21 (Trinket M0, Gemma M0, ItsyBitsy M0 Express) Guide, Files & Support

    so i borked the 3v point on the originial cap and still tried sticking solder to it, but ended up borking the cap right above it completely off the board. Next time i know how not to bork the 3v point, and if it is borked, properly identify the borked and not continue trying to stick wires to...
See more