On dat0/cmd 70R should be ok. But keep the clk at 47RAre there any 20-100R resistors on the V1/V2 motherboardboard? i need one ASAP if anybody knows. Ill also get to measuring in the meantime
Could i get away with 70R or 130 R on dat0/cmd?
It has to be named payload.Does the payload has to be named payload.bin or it'll open any kind of bin file??
Which LED should I look at?? The one from picofly board??
There is an LED around home buttonIt has to be named payload.
There is no other led on the switch so the picofly Led is the only one u can look at :-)
Everything is on the guide from the first page of this thread:Is there any full tutorial in what I need to buy? The installing won't be a problem, but I can't seem to find what I need to buy and where? Have been searching aliexpress and gbatemp for hours now. (Preferably with the flex cable)
I’ve noticed the 10/20 pieces lot of cpu flex cables are no longer available either. Guess I better up my mosfet gamelooks like the old sellers I used to get from on ali are gone..
The LED signaling seem to work ok on clones as long as they are on fw v.2.67.Hi,
Anyone have tried some RP2040tiny clone ?
I have trouble with programmation, no led reaction on last FW and led stay green on an old one.
If some have a solution ?
Thanks
View attachment 403554
I got a batch of those. The led doesn't light up with 2.75 for some reason. Another user suggested using 2.67 for the troubleshooting codes. If it checks out ok and glitches, just flash the latest firmware through picofly toolbox.Hi,
Anyone have tried some RP2040tiny clone ?
I have trouble with programmation, no led reaction on last FW and led stay green on an old one.
If some have a solution ?
Thanks
View attachment 403554
Beat me to it. And almost the exact same wording. LolThe
The LED signaling seem to work ok on clones as long as they are on fw v.2.67.
So I would suggest that you flash v.2.67, finish the installation, do the troubleshooting (if needed) and then, after you confirm that everything is working, flash the latest firmware from the toolbox in Hekate.
In 2.67 the red/blue flash led and finished on green and remains on green ( does not turn off ). And flash with pico toolbox in 2.73, no more led.The
The LED signaling seem to work ok on clones as long as they are on fw v.2.67.
So I would suggest that you flash v.2.67, finish the installation, do the troubleshooting (if needed) and then, after you confirm that everything is working, flash the latest firmware from the toolbox in Hekate.
Does the glitch work though? Using 2.67 is more for troubleshooting. Find the color codes if there's an error. If you can get into Hekate you are golden. And yes the LED won't work on 2.75. You don't need it if it's working, it's just the to look pretty and show off lol. I thought my install was bad cause I had no lights, but got the no SD screen.In 2.67 the red/blue flash led and finished on green and remains on green ( does not turn off ). And flash with pico toolbox in 2.73, no more led.
And In 2.67 I encounter a problem with the sd card detection boot.
Well, green is for success in 2.67. It might not turn off because as we know these clones don't communicate well with LED.In 2.67 the red/blue flash led and finished on green and remains on green ( does not turn off ). And flash with pico toolbox in 2.73, no more led.
And In 2.67 I encounter a problem with the sd card detection boot.
In 2.73 works fine, but in 2.67 I had SD card boot initialization errors. I check the SD card connector.Does the glitch work though? Using 2.67 is more for troubleshooting. Find the color codes if there's an error. If you can get into Hekate you are golden. And yes the LED won't work on 2.75. You don't need it if it's working, it's just the to look pretty and show off lol. I thought my install was bad cause I had no lights, but got the no SD screen.
What is your error code?any ideas guys? Happens with and without Emmc
Could the flex be faulty?
Seem s like some people are facing this issue:
https://github.com/Ansem-SoD/Picofly/issues/32