Hacking [Release] PS-Phive! (For PS4 FW 9.00) Exploit Host Menu

[xZenithy]

2900 default

Try to increase the time, test between 5.000 to 8.000-10.000, but you have to much failures, is not normal...

 

[Ashish999]

check previous posts from @Leeful in this thread to find the "right timing" for you.

here's are my screenshots, coming from shutdown and rest mode.

To "note" ; the 2 fails were only due to switching from esp Mode 1 to 2, and "other testing"".

My history blocker is on and browser settings accept cookies r disable.. is it effects any kind of exploit. I don't think so.. u r lucky..

Post automatically merged: Dec 23, 2022

Try to increase the time, test between 5.000 to 8.000-10.000, but you have to much failures, is not normal...

I

I tested with higher times like 5sec and 10 sec but works best with 2.9 sec..

 

[xZenithy]

My history blocker is on and browser settings accept cookies r disable.. is it effects any kind of exploit. I don't think so.. u r lucky..

Post automatically merged: Dec 23, 2022

I

I tested with higher times like 5sec and 10 sec but works best with 2.9 sec..

Then, maybe you have a poor connection signal between the s2 board to the rooter. That could explain this number of failures that you have...
Some rooters can tell you the quality of connection of his clients, check if it is below 80%...

 

[Maupiti]

Did a test with extended storage and app2usb drive connected at the same time, coming from shutdown, exploit fine (a bit longer than coming from rest mode)
but no issues with the exploit or running games

Post automatically merged: Dec 23, 2022

My history blocker is on and browser settings accept cookies r disable..

Reanable cookies and diseable history blocker.
There’s no point having a payload as history blocker to run

 

[Ashish999]

With history blocker enable and cookies enabled.. and change GoldHEN version stimulate result is here.. all r success.. thnx guys...

Post automatically merged: Dec 25, 2022

@Leeful bro Official GoldHEN 2.3 released.. please update site ..

 

[Leeful]

PS-Phive! v3 for PS4 Firmware 9.00 updated with latest GoldHEN v2.3

The v3 is exactly the same as the v3b (beta test) I did recently apart from:

• Added GoldHEN v2.3 to the host menu.
• Added a fix to the ESP bin to fix an issue if you entered the wrong home wifi SSID or the ESP could not connect to your home wifi network.
• Added a signal strength indicator to the ESP config page to show the signal strength of the connection to your home wifi network. (see image below)

v3 Host Menu link:
prb123.ir/ps-phive/v3/index.html
or just:
prb123.ir/ps-phive

v3 ESP32-S2 bin file:
prb123.ir/ps-phive/PS-Phive!_ESP32-S2_bin_v3.0.zip

I'll update the OP at a later date.

 

[Ashish999]

PS-Phive! v3 for PS4 Firmware 9.00 updated with latest GoldHEN v2.3

The v3 is exactly the same as the v3b (beta test) I did recently apart from:

• Added GoldHEN v2.3 to the host menu.
• Added a fix to the ESP bin to fix an issue if you entered the wrong home wifi SSID or the ESP could not connect to your home wifi network.
• Added a signal strength indicator to the ESP config page to show the signal strength of the connection to your home wifi network. (see image below)

View attachment 344291

v3 Host Menu link:
prb123.ir/ps-phive/v3/index.html
or just:
prb123.ir/ps-phive

v3 ESP32-S2 bin file:
prb123.ir/ps-phive/PS-Phive!_ESP32-S2_bin_v3.0.zip

I'll update the OP at a later date.

Op means bro?

 

[Leeful]

Op means bro?

original post.

 

[dudekpl]

@Leeful if I configure the connection to my own wifi network, is it possible for the ps4 to have access to the internet?

 

[Leeful]

@Leeful if I configure the connection to my own wifi network, is it possible for the ps4 to have access to the internet?

Yes.
Connect your PS4 to the esp first, go to the esp settings page, enter your home wifi details, connect your PS4 back to your home wifi.(wit alazifs dns etc)

You will then have internet access on your PS4 and the PS-Phive! menu will use the esp in [ESP MODE2].

 

[nubie]

@Leeful

I use esp mode 1 so far and this wierd thing keep happen

Wifi connection lost notif appear randomly , multiple times maybe 3 to 5 notif

They appear randomly , sometimes it's begin after 5 mins , sometimes 1 hour , sometimes 2 hours

My usb sleep time is default

I'm only change my usb wait times in config

Should I change this sleep times before loading goldhen ?

I change my usb wait times after loading goldhen

Post automatically merged: Dec 26, 2022

My esp32 isn't found when I trying to enter config page despite I can load goldhen twice for test after restart , I try first load goldhen than enter config , not found

Remove my esp32 than reconnect wifi , restart than load goldhen , try to enter config , not found again

Can't change sleep times , still default if my memory not wrong

I'm still using v3b here

 

[Leeful]

@Leeful

I use esp mode 1 so far and this wierd thing keep happen

Wifi connection lost notif appear randomly , multiple times maybe 3 to 5 notif

They appear randomly , sometimes it's begin after 5 mins , sometimes 1 hour , sometimes 2 hours

My usb sleep time is default

I'm only change my usb wait times in config

Should I change this sleep times before loading goldhen ?

I change my usb wait times after loading goldhen

Post automatically merged: Dec 26, 2022

My esp32 isn't found when I trying to enter config page despite I can load goldhen twice for test after restart , I try first load goldhen than enter config , not found

Remove my esp32 than reconnect wifi , restart than load goldhen , try to enter config , not found again

Can't change sleep times , still default if my memory not wrong

I'm still using v3b here

Go to Settings > Network > View Connection Status and tell me what it says in the following:

Signal Strength =
SSID =
IP Address Settings =
IP Address =
Subnet Mask =
Default Gateway =
Primary DNS =

Also when you enter the config, what IP does it say in the title at the top?
eg ...Using ESP IP: xx.xx.xx.xx

 

[nubie]

I will post it tomorrow

If my memory not wrong , alot of it is automatic
This is before I reapply my connection in network settings , need to use reset button in esp32 to make it appear in wifi

For config , I don't remember , just notif not found like when we need to enter flashdisk usb to jailbreak

 

[dudekpl]

@Leeful Unfortunately I'm still having trouble connecting
I did everything according to @xZenithy guide, but after restarting the console it won't load the exploit.
My settings
PS-Phive!_ESP32-S2_bin_v3.0
Signal Strength = 83%
SSID=netis_2.4G_798DEC
IP Address Settings=192.168.1.122
IPAddress=192.168.1.122
Subnet Mask =255.255.255.0
Default Gateway=192.168.1.1
Primary DNS = 165.227.83.145
SecDNS=192.241.221.79

 

[Maupiti]

@Leeful :

Flashed my esp32 with your new bin V3 , everything ok , including autoload latest Goldhen , but on the browser pqge see what's it says about Stats Pass / Failure : NaN ?
I did 2 or 3 shutdown to be sure that everything was running fine , but still : NaN

Post automatically merged: Dec 26, 2022

@Leeful Unfortunately I'm still having trouble connecting
I did everything according to @xZenithy guide, but after restarting the console it won't load the exploit.
My settings
PS-Phive!_ESP32-S2_bin_v3.0
Signal Strength = 83%
SSID=netis_2.4G_798DEC
IP Address Settings=192.168.1.122
IPAddress=192.168.1.122
Subnet Mask =255.255.255.0
Default Gateway=192.168.1.1
Primary DNS = 165.227.83.145
SecDNS=192.241.221.79

Huummm, what your posting are the ESP32 settings on your home wifi or PS4 settings ?

 

[Leeful]

@Leeful :

Flashed my esp32 with your new bin V3 , everything ok , including autoload latest Goldhen , but on the browser pqge see what's it says about Stats Pass / Failure : NaN ?
I did 2 or 3 shutdown to be sure that everything was running fine , but still : NaN

NaN (not a number) has nothing to do with anything on the ESP.
Something must have gone wrong when you initially cached the menu.
If you re-cache the menu it should be fine again.

 

[Ashish999]

I'm looking into it.

As it is in the original stooged code it looks like it should work but obviosly not:

  if (connectWifi && WIFI_SSID.length() > 0 && WIFI_PASS.length() > 0) {
    WiFi.setAutoConnect(true);
    WiFi.setAutoReconnect(true);
    WiFi.hostname(WIFI_HOSTNAME);
    WiFi.begin(WIFI_SSID.c_str(), WIFI_PASS.c_str());
    if (WiFi.waitForConnectResult() != WL_CONNECTED) {
    } else {
      IPAddress LAN_IP = WiFi.localIP();
      if (LAN_IP) {
        String mdnsHost = WIFI_HOSTNAME;
        mdnsHost.replace(".local", "");
        MDNS.begin(mdnsHost.c_str());
        if (!startAP) {
          dnsServer.setTTL(30);
          dnsServer.setErrorReplyCode(DNSReplyCode::ServerFailure);
          dnsServer.start(53, "*", LAN_IP);
        }
      }
    }
  }

if WiFi.waitForConnectResult() is not WL_CONNECTED, do nothing else do the wifi thing.

Maybe instead of receiving the "WL_CONNECTED" status it is receiving the "WL_IDLE_STATUS" which is trigering it to continue when it shouldnt.

I'll do some rewrite tests and see if I can fix it.

Obviosly it wont fix your problem of not being able to connect but at least it might fix the issue of it messing up the original access point if it cannot connect to whatever wifi settings it is given.

Post automatically merged: Dec 21, 2022

@xZenithy right, I've done some tests and it appears that the issue is that if the ESP cannot connect to the home wifi SSID that you enter it messes up the ESP and the regular access point no longer works.

Its ok if the password is wrong, that doesnt mess anything up but if the SSID is wrong or it cannot connect to the entered SSID (like in your case), things get messed up.

I've modified the wifi side of stooged's original script and now it doesnt mess up the ESP if it cannot to the home wifi SSID that is entered in the settings.

Below is a bin for you to test. Obviosly you still can't connect to your 5ghz network but it shouldn't mess up the ESP anymore if it cannot connect.

@Maupiti flash with this bin file.. this one is fixed ..

 

[Leeful]

@dudekpl Have you flashed the latest v3 bin? It now has a signal strength % on the esp config page if you are setup for using [ESP MODE2]
http://prb123.ir/ps-phive/PS-Phive!_ESP32-S2_bin_v3.0.zip

What signal strength does it show for your ESP?

 

[Maupiti]

NaN (not a number) has nothing to do with anything on the ESP.
Something must have gone wrong when you initially cached the menu.
If you re-cache the menu it should be fine again.

ok, will try and see how it goes ... tired tonight , obviously menu has nothing to "do" with esp32 bin

Post automatically merged: Dec 26, 2022

@Maupiti flash with this bin file.. this one is fixed ..

Well, I took the bin from latest post from @Leeful

PS-Phive! v3 for PS4 Firmware 9.00 updated with latest GoldHEN v2.3

The v3 is exactly the same as the v3b (beta test) I did recently apart from:

• Added GoldHEN v2.3 to the host menu.
• Added a fix to the ESP bin to fix an issue if you entered the wrong home wifi SSID or the ESP could not connect to your home wifi network.
• Added a signal strength indicator to the ESP config page to show the signal strength of the connection to your home wifi network. (see image below)

View attachment 344291

v3 Host Menu link:
prb123.ir/ps-phive/v3/index.html
or just:
prb123.ir/ps-phive

v3 ESP32-S2 bin file:
prb123.ir/ps-phive/PS-Phive!_ESP32-S2_bin_v3.0.zip

I'll update the OP at a later date.

Edit : Yep caching again and starting from scratch everything back to "normal" , I wonder if I cached an old menu , as I didn't have wifi strengh on the esp menu

 

[Ashish999]

ok, will try and see how it goes ... tired tonight , obviously menu has nothing to "do" with esp32 bin

Post automatically merged: Dec 26, 2022

Well, I took the bin from latest post from @Leeful

Edit : Yep caching again and starting from scratch everything back to "normal" , I wonder if I cached an old menu , as I didn't have wifi strengh on the esp menu

Bro r u using mobile hotspot for home wifi network.. can I use mobile hotspot??