Picofly AIO Thread

[minik1971]

good afternoon colleagues I have the rp2040-one but when I pass the 2.6 or any files thegood afternoon colleagues I have the rp2040-one but when I pass the 2.6 or any files the led does not turn on

 

[rehius]

good afternoon colleagues I have the rp2040-one but when I pass the 2.6 or any files thegood afternoon colleagues I have the rp2040-one but when I pass the 2.6 or any files the led does not turn on

you need 2.61

 

[minik1971]

you need 2.61

@rehius ready, the led on rp2040-one lights up green when passing the 2.61 file is normal

 

[angelC992]

Those are 47 000 Ohm. Use this and choose 47 Ohm: https://a.aliexpress.com/_mPVFw1q

Post automatically merged: Apr 6, 2023

You could even use 1/4W resistors, but you'll struggle to fit them. The 0805 fit quite well on the Pico pins, I imagine that you could get 1206 working as well. Show us some pics when you get it installed.

Those are 47 000 Ohm. Use this and choose 47 Ohm: https://a.aliexpress.com/_mPVFw1q

Post automatically merged: Apr 6, 2023

You could even use 1/4W resistors, but you'll struggle to fit them. The 0805 fit quite well on the Pico pins, I imagine that you could get 1206 working as well. Show us some pics when you get it installed.

Finally I used the 1206 ones.

 

[MXRD4K1LL4]

This is a Pikofly AIO Thread/Tutorial.
This information has been pulled from other threads and forums on this site, I haven't done anything except compile it in this one thread.
All credit goes to those who worked on all the relevant information and stuff.

First things First; I not not endorse piracy and those who released the firmware don't either so this is for home-brew use only.

DOING THIS MODIFCATION TO YOUR SWITCH MAY CAUSE PERMANENT DAMGE. I RECOMMEND YOU HAVE THIS DONE BY A PROFESSIONAL INSTALLER

DISCLAIMER! Me nor any of the other temp members who helped make this happen will be held liable to any damage you cause your console in attempting to mod it. Professional installation is recommended for this mod.

Just because a mod is cheap doesn't mean it's easy. - Trust me I learnt the hard way - Adran 2023

FW Changelog

General InformationInstallation overviewImagesCredits

1. 
   

   RequirementsBoard Pinout ListHintsLED IndicatorsFAQ's

   1. 
      
      • RP2040-Zero
      • SMD 0805 47 to 50 ohm Resistors
      • Mosfet (IRFHS8342 MOSFET) or cpu flex cable - I personally recommend - (lite flex for lites, v2 flex for v2 mariko etc etc)
      • switch (duh)
      • Wire
      • RP2040 Firmware (get the latest firmware from here FW 2.6 onwards doesn't need unlock)
   2. 
      !!!!PinOut for Other Boards!!!! (resistors / mosfets are still required)
      
      
      
   3. 
      
      
   4. 
      
      
   5. 
      
      
   
   
2. 
   
   
3. 
   

   Mosfet ImagesSolder Points

   1. 
      
      
      
      
      
      
   2. 
      
      
      
      
      
      
      
      
      
      
   
   
4. 
   
   

Changelog:
8-April-2023
Added FW 2.61 and changelog

7-Apr-2023
- Fixed size Mistake
- Added Firmware 2.6Alpha
-added Firmware 2.6a changelod and more board support pinout.

29-mar-2023
- Added link to Toshiba Firmware for rp2040
- Added alternative mosfets
- Added Erista (patched) diagram

P.S More formatting and information to cum

 

[linuxares]

Can someone tell me how they soldered on the emmc board?
Personally it does not stick and is pretty hard (it do not work)

Or if there's an easier place to solder

If you don't know how to do that. This mod really isn't something you should try.

 

[Dee87]

Can someone tell me how they soldered on the emmc board?
Personally it does not stick and is pretty hard (it do not work)

Or if there's an easier place to solder

u ever heard of flux?

i would suggest let someone else do it

 

[MXRD4K1LL4]

[]

 

[linuxares]

I know how it just don't work
Like i maybe didn't used the good wire

Flux... you need flux

 

[Dee87]

I know how it just don't work
Like i maybe didn't used the good wire

apparently u dont know how to Xd
if u knew u wouldnt be asking Xd

 

[rehius]

@rehius ready, the led on rp2040-one lights up green when passing the 2.61 file is normal

need to swap colours by using RGB mode jumper. short pin 29 to GND as the picture says

 

[Dee87]

@rehius ready, the led on rp2040-one lights up green when passing the 2.61 file is normal

set rgb mode

 

[minik1971]

need to swap colours by using RGB mode jumper. short pin 29 to GND as the picture says

@rehius and the rp2040-one is already fully functional with 2.6.1?

 

[Adran_Marit]

@rehius and the rp2040-one is already fully functional with 2.6.1?

Yes it works

 

[A-Hacked-Soul]

its perfect dont need thicker wire i do all installs with 0.1mm wire
u dont need more

Any advice? This is thinner than I am used to

 

[Dandan0404]

need to swap colours by using RGB mode jumper. short pin 29 to GND as the picture says

set rgb mode

If i already flashed the uf2 and had green. I must bridge it right ti get Red for RGB? How do i check it? Should i reflash then again the same uf2??

 

[Dee87]

Any advice? This is thinner than I am used to

Get used to it ;-)

 

[rehius]

If i already flashed the uf2 and had green. I must bridge it right ti get Red for RGB? How do i check it? Should i reflash then again the same uf2??

to check you can either reflash it again, or just power it on (without NS you should see proper colours Blue -> Purple)

 

[Ernestino]

Yes it works

rp2040-one working since 2.6 alpha FW.
I have cut off USB connector after flashing via USB.
Later updated via Picofly toolbox to 2.61. No problems so far...

 

[cicci084]

That was you mistake, video guides always are outdated and sometimes wrong.

you can read the guide:

https://rentry.org/switchHackingIsEasy

for understand the basics configurations.

you need to understand how the file HEKATE_IPL.ini the explanation is on the hekate page:

https://github.com/CTCaer/hekate#bootloader-configuration

when you put the autoboot=2 pointing to a config (on this case the second of the file), and the config have the EmuMMC you always will autoboot on it, by example:

{--- EMUNAND START---}
[CFW (EMUMMC)]
id=EMUNAND
emummcforce=1
fss0=atmosphere/package3
atmosphere=1
logopath=bootloader/EnergyStarBL.bmp
icon=bootloader/res/payload_hue_nobox.bmp
kip1patch=nosigchk
{--- EMUNAND END ---}

Post automatically merged: Apr 9, 2023

note this is my configuration, and as I have custom icon and logo the sentences point to mines.

but emummcforce, fss0 and atmosphere ones are the needed to force emmummc

First, thanks for you reply.
Honestly, after doing all the backups in the hekate settings I found all the settings I personally need.
The video link is very updated and detailed, I don't think I did something wrong.
I didn't need to edit any files, I configured everything from the autoboot settings.

Post automatically merged: Apr 10, 2023

Another question.
Where can I find the picofly toolbox and the procedures to update the FW with this tool?
Thanks, good job.